|
汽车覆盖件内凹圆弧翻边仿真与变形控制研究
|
|
英文标题：Numerical simulation and deforming control of concave curvature flanging in automobile panels |
|
作者：韩东风 林建平 陈水生 管华军 |
|
单位：同济大学机械工程学院 上海大众汽车有限公司 |
|
关键词：翻边 圆弧曲面不光顺 工艺参数 |
|
分类号：TG386.3;U463 |
|
出版年,卷(期):页码：2009,34(6):83-87 |
|
摘要：
|
|
分析了汽车覆盖件圆弧曲面不光顺发生区域的几何特征,指出内凹型翻边是缺陷产生的原因。提取了内凹翻边的几何模型并利用板料成形仿真软件ETA/Dynaform对翻边成形过程进行仿真,结果表明,翻边时圆弧过渡区受周向的剪应力,这个剪应力是圆弧不光顺产生的诱因。通过改变翻边几何参数和工艺参数得到了这些因素对圆弧不光顺的影响规律,结果表明:随着动模圆角半径和翻边高度的增大,圆弧不光顺有加重的趋势;减小定模圆角半径、动定模间隙、翻边轮廓圆弧半径和摩擦系数可以改善圆弧不光顺。
|
|
By analyzing the geometry of the forming part,it is figured out that concave curvature flanging causes the uneven arris. The geometry of concave curvature flanging in flat plane was abstracted and the flanging process was simulated with sheet-metal forming FED codes ETA/Dynaform. Result shows that the circumferential shearing stress in the arris region causes the defect. Then the process parameters were studied and several rules were concluded that uneven tendency increases with increasing radius of punch and the flanging height,while the defect can be reduced by decreasing the radius of die,clearance ,flanging contour curvature and the friction coefficient.
|
|
基金项目：
|
|
|
|
作者简介：
|
|
|
|
参考文献：
|
[1]Wang C T,Gary Kinzelu,Taylan Altan.Failure and wrink-ling criteria and mathematical modeling of shrink and stretch flanging operations in sheet-metal forming[J].Journal of Materials Processing Technology,1995,(53):759-780.
[2]刘志云,何成宏,杨国泰,等.外缘外曲翻边时的应力应变分析[J].塑性工程学报,2004,11(2):32-35.
[3]刘志云,何成宏,杨国泰,等.外缘内曲翻边时的应力应变分析[J].锻压装备与制造技术,2003,(4):28-31.
[4]李大永,罗应兵,尹纪龙,等.V型伸长翻边解析与数值研究[J].材料科学与工艺,2004,12(5):497-500.
[5]刘天聪.翻边成形件的常见缺陷及修正方法[J].模具技术,2000,(4):70-73.
[6]伊绍亭.翻边工序中的问题和解决方法[J].模具工业,1979,(2):114-116.
[7]崔令江.汽车覆盖件冲压成形技术[M].北京:机械工业出版社,2003.
[8]Li C F,Yang Y Y,Li Shuoben.Deformation analysis and die-design principles in shrink-curved flanging[J].Journal of Materials Processing Technology,1995,(51):164-170.
|
|
服务与反馈：
|
|
【文章下载】【加入收藏】
|
|
|
|
