|
基于Deform的轴承钢球冷镦工艺的优化设计
|
|
英文标题：Optimization design of cold upsetting process in steel bearings ball based on Defrom |
|
作者：傅蔡安 华新锋 王贤 |
|
单位：江南大学机械工程学院 |
|
关键词：冷镦模具 Deform 正交试验 钢球球坯 |
|
分类号：TG316 |
|
出版年,卷(期):页码：2010,35(1):154-158 |
|
摘要：
|
|
现有钢球冷镦工艺生产的钢球环带、两极比较大,材料利用率不高,这不仅增加了后续加工时间,而且造成很大浪费。为了降低球坯余量,进一步节约材料,提高生产效率,通过对锥鼓形球坯冷镦工艺的研究,建立了饱满度、圆度、冷镦力、体积等评价指标,并设计正交试验,用Deform仿真分析得出合理的球坯工艺参数。结果显示,优化后的球坯冷镦力减小了35%,改进后的工艺参数具有很好的实际应用价值。
|
|
The largeness of circumferential belt and two poles in ball billet after cold upsetting process and the consequently low material utilization ratio increase the following process time and cause a great waste.In order to obtain low allowance of ball billet,high material utilization ratio and productivity,through the research of the cold upsetting process,the evaluating index including plumpness,roundness,cold upsetting force and volume was established,and orthogonal test was designed.By the Deform simulation analysis,the optimum process parameters were obtained.The results show that the optimized cold upsetting force is reduced by 35%.So the optimized process parameters has a great practical application value.
|
|
基金项目：
|
|
|
|
作者简介：
|
|
|
|
参考文献：
|
[1]王宝振.国外钢球制造技术简介(二)[J].轴承,1999,(2):39-41.
[2]彭大暑.金属塑性加工原理[M].长沙:中南大学出版社,2004.
[3]赵学军.锥鼓形球坯体积计算[J].轴承,1986,(2):11-13.
[4]吴有炜.实验设计与数据处理[M].苏州:苏州大学出版社,2002.
[5]夏新涛,马伟,颉谭成,等.滚动轴承制造工艺学[M].北京:机械工业出版社,2007.
[6]冯伟敏.冷镦工艺尺寸附表三[R].无锡:无锡钢球厂,2005.
[7]李传民,王向丽,闫华军,等.Deform 5.03金属成形有限元分析实例指导教程[M].北京:机械工业出版社,2006.
[8]杜平安.有限元网格划分的基本原则[J].机械设计与制造,2000,(1):34-36.
[9]Hyunkee Kim,Kevin Sweeney,Taylan Altan.Applicationof computer aided simulation to investigate metal flow in se-lected forging operations[J].Journal of Material ProcessingTechnology,1994,46(1-2):127-154.
[10]施志辉,刘杰.优化计算切削用量的实用方法[J].工具技术,2008,(1):86-89.
[11]葛华伟,贺霞.改进钢球生产工艺与提高钢球制造精度等级[J].黑龙江科技信息,2003,(11):136-137.
|
|
服务与反馈：
|
|
【文章下载】【加入收藏】
|
|
|
|
