锻压技术

单点渐进成形中成形角对成形极限的影响

英文标题：Effect of forming angles on formability in single point incremental forming

作者：姜虎森李先珍

分类号：TG386.4

出版年,卷(期):页码：2009,34(6):74-76

摘要：

在单点渐进成形中,成形零件的厚度满足正弦定律,成形极限用最大成形角表示。本文设计了测定板料最大成形角的试验装置并通过两组试验来测定LY12M的最大成形角。首先用曲线斜率为变量的旋转类零件初步确定最大成形角范围,然后再用曲线斜率为定值的旋转类零件确定真实最大成形角。经测定,铝板LY12M的真实最大成形角为65°。该方法用来测定板料的最大成形角是简单、可行的。

In single point incremental forming(SPIF),the final thickness of a deformed sheet can be predicted by the sine law,the formability in SPIF can be expressed as the maximum wall angle that a sheet would endure without fracturing. The experimental set-up was designed and the maximum wall angle for aluminum sheet LY12M was investigated by two tests. In the first test,the approximate maximum wall angle by forming the varietal wall angle conical frustum was obtained. In the second test,the conical frustums and obtained the maximum actual wall angles was designed. The maximum actual wall angles for aluminum sheet LY12M was 65°. This method is simple and feasible in predicting the maximum wall angle.

基金项目：

山东省教育厅科技计划项目(J07YJ17)

参考文献：

[1]Matsubara.Acomputer numerically controlled dieless incre-mental forming of a sheet metal Proceedings of the Institution of Mechanical Engineers[J].Journal of Engineering Manu-facture,2001,215(7):959-966.
[2]Ki m TJ,Yang D Y.I mprovement of formability for the in-cremental sheet metal forming process[J].International Journal of Mechanical Sciences,2000,(42):1271-1286.
[3]Ambrogio G,De Napoli L.Application of incremental form-ing process for high customized medical product manufactur-ing[J].Journal of Materials Processing Technology,2005,(162):156-162.
[4]张士宏,吴江.薄壁不锈钢管滚珠旋压成形工艺研究[J].锻压技术,2009,34(1):60-64.
[5]李亚非,陈辉.薄壁铝合金锥形件旋压过程的缺陷分析[J].锻压技术,2008,33(3):56-59.
[6]Iseki H.An approxi mate deformation analysis and FEManal-ysis for the incremental bulging of sheet metal using a spheri-cal roller[J].Journal of Materials Processing Technology,2001,(111):150-154.
[7]Hussain G,Gao L,Dar N U.An experi mental study on some formability evaluation methods in negative incremental forming[J].Journal of Materials Processing Technology,2007,(186):45-53.
[8]Wei Hongyu,Gao Lin.Investigation onthickness distribution along bulge type incrementally formed sheet metal part with irregular shapes[A].Proceedings of the International Manu-facturing Conference[C].Journal of Shandong University,2004.
[9]Hussain G,Gao L,Dar N U.A comparative study on the forming li mits of an aluminum sheet-metal in negative incre-mental forming[J].Journal of Materials Processing Tech-nology,2006,(186):45-53.

服务与反馈：

【文章下载】【加入收藏】