|
摘要：
|
|
反向滚珠旋压应用于成形带有纵向内筋的薄壁筒形件。以刚塑性有限元法为基础,应用商业有限元软件DE-FORM-3D V6.0分析了纵向内筋薄壁筒形件反向滚珠旋压成形金属塑性变形区的应力状态,研究了金属塑性变形时的流动规律。有限元模拟结果表明,纵向内筋薄壁筒形件反向滚珠旋压过程中,变形区金属处于三向压应力状态,而且沿着旋压件壁厚方向,从内向外等效应力值和等效应变值逐渐增加。
|
|
Backward ball spinning was applied to thin-walled tube with longitudinal inner ribs.The state of stresses in the deformation zone was analyzed and the law of plastic flow of the metal in the deformation zone was studied by means of commercial finite element software DEFORM-3D V6.0 during backward ball spinning of thin-walled tubular part with longitudinal inner ribs.FEM results show that during backward ball spinning of thin-walled tubular part with longitudinal inner ribs,the metal in the deformation zone is caused to be in a three-dimension compressive press state,and along the direction of wall thickness of the spun part,the effective stress value and the effective strain value gradually increase from the inner surface to the outer surface.
|
|
基金项目：
|
|
黑龙江省博士后基金资助
|
|
作者简介：
|
|
|
|
参考文献：
|
[1]赵云豪,汪发春,沈健.TB2钛合金筒形件旋压变形组织性能的研究[J].锻压技术,2007,32(6):87-89.
[2]徐文臣,单德彬,陈宇,等.钛合金薄壁筒形件热旋成形技术研究[J].锻压技术,2008,33(3):56-59.
[3]赵腾伦,黄建峰,张清泉,等.筒形件反旋成形有限元数值模拟[J].锻压技术,2008,33(1):60-65.
[4]江树勇,薛克敏,李春峰,等.铝合金薄壁筒形件滚珠旋压成形分析[J].锻压技术.2005,30(4):24-26.
[5]江树勇,薛克敏,李春峰,等.基于神经元网络的薄壁筒滚珠旋压成形缺陷诊断[J].锻压技术,2006,31(3):79-83.
[6]Jiang Shuyong,Ren Zhengyi.Analysis of mechanics in ballspinning of thin-walled tube[J].Chinese Journal of Mechan-ical Engineering,2008,21(1):25-30.
[7]江树勇,顾卫东,李春峰,等.纵向内筋薄壁筒反向滚珠旋压成形机理研究[J].锻压技术,2008,33(5):88-91.
[8]Jiang Shuyong,Ren Zhengyi,Wu Bin et al.General issues ofFEMin thin-walled tubular part with longitudinal inner ribs[J].Transactions Nonferrous Metals Society of China,2007,17(4):793-798.
[9]江树勇,郑玉峰,赵立红,等.基于有限元法纵向内筋薄壁筒反向滚珠旋压分析[J].塑性工程学报,2009,16(2):80-84.
|
|
服务与反馈：
|
|
【文章下载】【加入收藏】
|
|
|
|
