|
摘要：
|
|
对杯形薄壁梯形内齿旋压成形过程进行了试验研究,研究了道次压下量、进给比、旋压方式及旋轮型面对杯形薄壁梯形内齿齿形填充的影响规律。结果表明,道次压下量是影响内齿轮旋压过程中最主要的工艺参数。提出采用错距旋压工艺、改变主轴转向和轴向加压等措施来减轻或消除轮齿沿轴向或切向填充不均匀、轮齿与齿槽部分轴向伸长量存在差异等缺陷,并利用试验所获得的优化工艺参数,研制出质量合格的内齿样件。
|
|
The experimental research on the spin-forming of cup-shaped thin-walled trapezoidal inner-gear was carried out.The influence of various parameters on the tooth profile forming was investigated experimentally,including thickness reduction per pass,feed rate of rollers,spinning methods and surface-shape of roller.It shows that the thickness reduction per pass is the main parameter influencing the spin-forming of trapezoidal inner-gear.The defects of non-uniform distribution of tooth height along axial or tangential direction,the difference of the axial elongation between the gear tooth and groove etc.,can be decreased or eliminated by stagger spinning,changing rotation direction of main spindle,and applying a pressure force to the opening-end of workpiece along axial direction.The qualified samples are produced based on the optimized forming parameters obtained by experiment.
|
|
基金项目：
|
|
国家自然科学基金资助项目(50475097);;
广东省自然科学基金面上重点项目(04105943);;
广东省科技计划项目(2006B11901001)
|
|
作者简介：
|
|
|
|
参考文献：
|
[1]李继贞,祝昕.带内齿工件的旋压成形[J].锻压技术,1997,22(2):36-37.
[2]Maschinenbau and Blechformtechnik GmbH&Co.KG:In-onovation in Chipless Forming Technology[EB/OL]:2002.
[3]夏琴香,李小曼,李小龙,等.杯形薄壁梯形内齿旋压件的制取及金相组织的研究[J].锻压装备与制造技术,2008,(1):88-91.
[4]夏琴香,杨明辉,陈家华,等.工艺参数对杯形薄壁内啮合齿轮旋压成形影响的数值模拟研究[J].塑性工程学报,2006,13(4):1-5.
[5]夏琴香,杨明辉,胡昱,等.杯形薄壁矩形内齿旋压成形数值模拟与试验[J].机械工程学报,2006,42(12):192-196.
[6]夏琴香,胡昱,孙凌燕,等.旋轮型面对矩形内齿旋压成形影响的数值模拟[J].华南理工大学学报,2007,35(8):1-6.
[7]程秀全,许业华,夏琴香.框架式三旋轮错距旋压成形装置的研制[J].锻压装备与制造技术,2005,(6):31-35.
|
|
服务与反馈：
|
|
【文章下载】【加入收藏】
|
|
|
|
