|
负间隙精密冲裁最佳负间隙的合理取值
|
|
英文标题：Reasonable value of optimized negative clearance in fine-blanking with negative clearance |
|
作者：李建华 张忠美 |
|
单位：中原工学院机电学院 |
|
关键词：负间隙 有限元模拟 无飞边 |
|
分类号：TG386.2 |
|
出版年,卷(期):页码：2009,34(1):149-153 |
|
摘要：
|
|
基于相似理论基础建立了刚塑性有限元仿真几何模型,采用金属塑性有限元分析软件DEFORM-2D对AISI-1045钢进行了不同负间隙冲裁的模拟与分析,获得了不同负间隙值与塌角、剪切带、冲裁力的关系曲线。并依据模拟的结果对3.8 mm厚的45钢进行了不同负间隙值的冲裁实验,获得了剪口质量好且无毛刺的冲裁件,总结出负间隙值c取-0.1~-0.15 mm时可以实现无毛刺精密冲裁。
|
|
The geometry model of the rigid-plastic Finite Element Model(FEM) was established based on the similarity theory.The blanking of AISI-1045 material with different negative clearance values was simulated and analyzed by finite element analysis software of metal plastic DEFORM-2D to obtain the relation curve of different negative clearance values with roll-over,sheared zone and punching load.According to the result of simulation,the blanking experiments of AISI-1045 material with 3.8 mm thickness and different negative clearances were made and the samples with well sheared cut without burrs were obtained by experiments.It summarizes that fine blanking without burrs can be achieved when the negative clearance value c is of-0.1——0.15 mm.
|
|
基金项目：
|
|
河南省科技厅基础研究项目(0311051000)
|
|
作者简介：
|
|
|
|
参考文献：
|
[1]李建华,范为福,杜虹.无飞边冲孔瞬时间隙及塑性状态研究[J].中国机械工程,2002,13(12):1065-1066.
[2]范为福,黎刚生,乔国谦.AISI-1045、1025钢的冲裁模拟[J].锻压技术,2007,32(4):120-124.
[3]李建华,乔国谦,黎刚生.铝板负间隙冲裁力与间隙的研究[J].锻压装备与制造技术,2006,41(6):64-66.
[4]孙希延,施浒立,纪元法,等.板料拉深成形数值模拟关键算法的比较[J].锻压技术,2006,31(2):19-22.
[5]秦泗吉,彭加耕.厚板对冲裁力影响规律的研究[J].金属成形工艺,2002,20(4):4-7.
[6]温彤,廖林灿,张湘伟.金属剪切过程的理论研究状况[J].锻压技术,2000,25(3):44-47.
[7]彭加耕,秦泗吉,李硕本.板材精密冲裁工艺的研究[J].燕山大学学报,2002,26(4):347-350.
|
|
服务与反馈：
|
|
【文章下载】【加入收藏】
|
|
|
|
