|
Ti-6Al-4V钛合金等通道转角挤压有限元模拟
|
|
英文标题：Three dimensional finite element analysis of Ti-6Al-4V alloy during equal channel angular pressing |
|
作者：张晨 李淼泉 罗皎 林莺莺 |
|
单位：西北工业大学材料学院 |
|
关键词：钛合金 等通道转角挤压 有限元 |
|
分类号：TG379 |
|
出版年,卷(期):页码：2008,33(5):102-106 |
|
摘要：
|
|
对Ti-6Al-4V钛合金的等通道转角挤压过程进行三维有限元模拟,分析不同的凸模下压速度对等通道转角挤压过程的影响,并结合实际的挤压过程考虑挤压后残留在模具出口通道内的残余试样对挤压下一根试样的影响。结果表明:挤压速度的提高对应力、载荷和温升的影响很大,对应变速率很敏感的钛合金应在有效细化晶粒的前提下降低挤压速度,试验中挤压速度取0.3 mm.s-1;残余试样的存在使变形更均匀,但增加了挤压下一根试样时的初始阶段的载荷。
|
|
Three dimensional finite element simulation was carried out during equal channel angular pressing of Ti-6Al-4V alloy,the effects of extrusion speed and retained sample that remained in the die export channel after ECAP on extrusion process were studied.The results show that extrusion speed deeply affects effective stress,extrusion load and temperature field.It should take low extrusion speed on the premise of effective grain refinement for Ti-6Al-4V alloy which is very sensitive to strain rate.In the experiment,appropriate extrusion speed was 0.3 mm·s-1.Retained sample improves the uniformity of deformation,but it causes the increase of extrusion load in the next sample extrusion stage.
|
|
基金项目：
|
|
|
|
作者简介：
|
|
|
|
参考文献：
|
[1]Valiev R Z,Islamgaliev R K,Alexandrov I V.Bulk nanostruc-tured materials from severe plastic deformation[J].Progressin Materials Science,2000,45(2):183-186.
[2]毕见强,周慧.大塑性变形法制备块体纳米材料[J].金属成形工艺,2002,20(6):43-45.
[3]毕见强,孙康宁.等效应变量对等径角挤压的2A12铝合金力学性能的影响[J].塑性工程学报,2005,12(6):42-44.
[4]Zhernakov V S,Latysh V V,Zharikov A I.Developing ofnanostructured SPD Ti for structural use[J].Scripta Materia-lia,2001,44:1771-1774.
[5]Valiev R Z.Ultrafine-grained materials prepared by severeplastic deformation[J].Annales des Chimie.Science des Ma-teriaux,1996,21:369-370.
[6]王德胜,侯英玮.ECAP法对H62黄铜的晶粒细化研究[J].锻压技术,2006,31(2):39-42.
[7]Semenova I P,Raab G I,Saitova L R.The effect of equal-channel angular pressing on the structure and mechanical be-havior of Ti-6Al-4V alloy[J].Materials Science and Engi-neering,2004,A387-389:805-808.
[8]刘英,李元元,张大童.金属材料的等通道转角挤压研究进展[J].材料科学与工程,2002,20(4):613-617.
[9]Yamashita A,Horita Z,Langdon T G.Improving the me-chanical properties of magnesium and a magnesium alloythrough severe plastic deformation[J].Materials Science andEngineering,2001,A 300:142-147.
[10]周眀智,薛克敏,李萍.静水压力对粉末多孔材料等径角挤压过程的影响[J].锻压技术,2007,32(2):53-56.
[11]Yapici G G,Karaman I,Luo Z P.Mechanical twinning andtexture evolution in severely deformed Ti-6Al-4V at high tem-peratures[J].Acta Materialia,2006,54:3755-3771.
|
|
服务与反馈：
|
|
【文章下载】【加入收藏】
|
|
|
|
