|
摘要：
|
|
通过采用主应力法导出考虑纵向变形速度和横向加速度的镦粗变形力的计算公式,并用算例讨论了超塑性材料变形力的计算方法、变形力随时间的变化规律,以及纵向变形速度和横向加速度对变形力的影响大小。由于主应力方法适合于a/h不太小的情况,因此导出的公式也应该满足这一条件。变形力可以分成qj,qy,qd3项,其中qd在ρV2/k极小于1时,可以忽略不计;但是当ρV2/k接近于1时就不可忽略。接触面的分布压力的最大和最小值的位置和一般率无关的塑性材料镦粗时的位置一样,分别在x=0和x=±a/2处。
|
|
The calculating formula of upsetting forming pressure considering longitudinal forming velocity and transverse acceleration has been conducted by using main stress method in this paper.The calculating method,the relation between the forming pressure and time,and the affection of longitudinal forming velocity and transverse acceleration to the forming pressure are discussed through an example.Main stress method is suitable when a/h is not too small.Therefore,the formula obtained in this paper should be also a meet for this condition.The forming pressure is divided into three items: q_j,q_y,q_d.q_d is neglectful when ρV~2/k is far smaller than 1;q_d is not neglectful when ρV~2/k is close to 1.The position of maxium and minimum distribution pressure is the same as that of common upsetting of velocity-independent plastic material.The maximum pressure is at where x=0 and the minimum pressure is at where x=±a/2.
|
|
基金项目：
|
|
淮海工学院学科建设基金资助项目(XK2003-02);;
淮海工学院自然科学基金资助项目(Z2002006);;
固体力学教育部重点实验室(同济大学)开放课题(200003)
|
|
作者简介：
|
|
|
|
参考文献：
|
[1]Barnes A J.Industrial application of superplasticity forming:trends and prospects[J].Materials Science Forum,2001,357 359:3 16.
[2]Sanders Daniel G.The current state-of-the-art and the future inairframe manufacturing using superplastic forming technologies:trends and prospects[J].Materials Science Forum 2001,357359:17 22.
[3]Li Zhiqiang,Zhu Hanliang.Industrial application of superplas-ticity forming technology in China[J].Materials Science Fo-rum,2001,357-359:53 58.
[4]洪慎章,曾振鹏.超塑性模锻工艺的应用和发展[J].锻压技术,2000,(1):44 46.
[5]金泉林.超塑变形的力学行为与本构描述[J].力学进展,1995,25(2):261 275.
[6]汪大年.金属塑性成型原理[M].北京:机械工业出版社,1982.
[7]王祖唐,关廷栋,肖景容,等.金属塑性成形理论[M].北京:机械工业出版社,1989.
[8]王连东,李仕华,刘助柏.镦粗工艺理论与技术的研究和进展[J].中国机械工程,2001,12(4):474 477.
[9]贾乃文.横向变形速度对超塑性材料压缩变形力的影响[J].金属成形工艺,1990,(4):32 34.
[10](英)罗(Rowe.G.W.)著,张子公,陈金德,陈楚杰,等译.工业金属塑性加工原理[M].北京:机械工业出版社,1984.
[11]Vasin R A,Enikeev F U,Tokuda M,Safiullin RV.Mathematical modeling of the superplastic forming of a longrectangular sheet[J].International Journal of Non-LinearMechanics,2003,38(5):799 807.
[12]徐秉业,陈森灿.塑性理论简明教程[M].北京:清华大学出版社,1981.
[13]林治平.锻压变形力的工程计算[M].北京:机械工业出版社,1986.
[14]祝汉良,辛志峰,李志强,等.高应变速率超塑性研究新进展[J].航空制造技术,2000,(5):13 16.
|
|
服务与反馈：
|
|
【文章下载】【加入收藏】
|
|
|
|
