锻压技术

差厚拼焊板辊弯成形仿真研究

英文标题：Simulation of roll forming process for tailorwelded blank with different thicknesses

作者：李敏韩飞刘继英

单位：北方工业大学

分类号：TG316

出版年,卷(期):页码：2011,36(4):50-55

摘要：

利用MSC.MARC软件对差厚拼焊板辊弯成形过程进行了数值模拟分析，探讨了薄厚两侧等效应力不均匀性的产生原因并给出了其分布规律，对比分析了同种材料薄厚两侧应力的差异。通过对薄厚两侧的回弹角的对比分析表明:当板厚比为0.67时，材料强度比为1.4时可以得到较好的成形结果；当强度比为1时，材料板厚比小于2时可以得到较好的成形结果。

The finite element software MSC.MARC was used to simulate tailor welded blanks of different thickness ratios by roll forming. The reason of non uniform equivalent stress along cross section was analyzed and the distribution characteristics was given. When two side thickness ratio is 0.67,the result of the present study suggests that the best strength ratio is 1.4; when the strength ratio is 1, the study result suggests that the forming result would be good when the thickness ratio is lower than 2.

基金项目：

北京市自然科学基金资助项目（3112010）；北京市教育委员会科技发展计划面上项目（KM201010009001）；北京市中青年骨干人才培养计划（PHR20110851）

参考文献：

[1] 史永凌.先进高强度钢辊弯成型有限元仿真研究[D].北京：北方工业大学, 2006.

[2] 曾钢，袁少波.拼焊板在汽车工业中的应用[J]. 电焊机，2004，34（6）:12-15.

[3] Ganesh Narayanan R, Narasimhan, K. Predicting the forming limit strains of tailor welded blanks[J]. Strain Analysis for Engg. Des.,2008,43(7):551-563.

[4] Anand D,Boudreau G, Andreychuk P. Forming behaviour of tailor (laser) welded blanks of automotive steel sheet[J]. Canadian J. Metallurgy and Mat. Sc.,2006，45(2): 187-197.

[5] Chan S M, Chan L C, Lee T C .Tailor welded blanks of different thickness ratios effects on forming limit diagrams[J].Journal of Materials Processing Technology, 2003，132: 95-101.

[6] Siegert K,Glashbrenner B.Forming of tailor blanks with non linear weld lines[J]. SAE Papers,2000,414(1):27-31.

[7] Kinsey Brad,Viswanathan Vikram,Cao Jian.Forming of aluminum tailor welded blanks[C]. SAE World Congress, 2001, 3:5-8.

[8] 武立波, 宋若冰. 拼焊板成形极限研究进展[J].锻压技术，2006,31(3)：19-22.

[9] Lindgren M. Cold roll forming of a U channel made of high strength steel[J]. Journal of Materials Processing Technology, 2007，186：77-81.

[10] 刘广达，李云涛，张建，等.不等厚异质高强钢拼焊板塑性变形性能研究[J]. 物理测试, 2009,27 (1)：5-8.

[11] 卜高乐. 变截面冷弯成型的FEA仿真研究[D]. 北京：北方工业大学,2007.

[12] 周杰, 高超.拼焊板U形件冲压成形中焊缝移动与回弹的研究[J].热加工工艺，2009，38(21):90-96.

[13] 薛松,周杰. 拼焊板板厚差比对成形性能的影响[J].模具工业,2008，34(7):34-38.

服务与反馈：

【文章下载】【加入收藏】