锻压技术

高强度钢板V形弯曲板厚方向压缩对回弹的影响

英文标题：Effect of thickness direction compression on springback of high strength V shape sheet

作者：陆宏黄文

单位：燕山大学

关键词：V形弯曲回弹高强度钢板弹塑性FEM

分类号：TG386

出版年,卷(期):页码：2011,36(4):56-59

摘要：

定量评价了V形弯曲凸模在到达下死点后在板厚方向的压缩作用对减小回弹的影响。利用弹塑性有限元法对高强度钢板V形件的弯曲成形和回弹过程进行模拟，并通过实验进行验证。模拟结果显示：回弹随平均压强与抗拉强度比值的增大而减小；凸模圆角半径对回弹的影响不大；有限元网格划分影响回弹的模拟结果，细分网格并在与凸模接触的部分增加单元数量可改善回弹模拟精度；2D平面应变单元细分网格的模拟结果与实验结果一致。

The effect of the compression between the punch and the die on springback after the punch reaching the dead point was evaluated. Utilizing the elasticplastic FEM, the forming and springback process of high strength V shape sheet was simulated. The investigation was also carried out through experiment. The result shows that springback decreases as the ratio of the average pressure and tensile strength increase. The radius of the punch and the die has little influence on the springback. Fine meshing can improve the precision of springback simulation. The results of 2D plain strain element with fine meshes are in good agreement with the experiment results.

基金项目：

教育部留学回国基金项目（A1026）

参考文献：

[1] Li X, Yang Y, Wang Y, et al. Effect of the material hardening mode on the spring back simulation accuracy of V free bending[J]. Journal of Materials Processing Technology, 2002,123:209-211.

[2] Cho J R, Moon S J, Moon Y H, et al. Finite element investi gation on springback characteristics in sheet metal U die bending process[J]. Journal of Materials Processing Technology, 2003, 141:109-116.

[3] Gomes C, Onipede O, Lovell M. Investigation of springback in high strength anisotropic steels[J]. Journal of Materials Processing Technology, 2005, 159:91-98.

[4] 赵军，苏春建，官英平，等.U形件弯曲影响回弹因素模拟分析[J]. 锻压技术，2007，32（6）:136-140。

[5] Annika Nilsson, Lars Melin, Claes Magnusson. Finiteelement simulation of V die bending: a comparison with experimental results[J]. Journal of Materials Processing Technology, 1997， 65：52-58.

[6] Li Xuechun, Yang Yuying, Yongzhi Wang, et al. Effect of the material hardening mode on the springback simulation accuracy of V free bending[J]. Journal of Materials Processing Technology, 2002, 123: 209-211.

[7] Sung Ho Chang, Jang Mo Shin, Young Moo Heo, et al. Springback characteristics of the tailor welded strips in U bending[J]. Journal of Materials Processing Technology, 2002, 130131: 14-19.

[8] 日本塑性加工学会.わかりやすいプレス加工[M].東京：日刊工業新聞社，2000.

[9] Mindlin R D. Influence of rotatory inertia and shear on flexural motion of isotropic elastic plates[J]. J. Appl. Mech. ，1951, 18: 31-38.

[10] Reissner E. The effect of transverse shear deformation on the bending of elastic plates[J]. J. Appl. Mech.， 1945, 12: 69-76.

服务与反馈：

【文章下载】【加入收藏】