锻压技术

U形件模具表面摩擦对回弹影响的数值模拟

英文标题：Numerical simulation of U-bending die surface's friction influence on springback

作者：符永宏王忠领华希俊许华施余峰

单位：江苏大学

关键词：U形弯曲摩擦系数回弹模具冲压

分类号：TH161.14

出版年,卷(期):页码：2011,36(6):28-32

摘要：

通过对U形件模具表面进行激光复合造型处理，有效的控制模具表面各区域的摩擦系数，从而改善了板料的回弹，同时提高了模具的寿命。利用ABAQUS100有限元模拟软件对U形件进行数值模拟，在模具表面各区域设置不同的摩擦系数，揭示了各区域摩擦系数对U形件回弹的影响规律。结果表明：增加凹模圆角、法兰区与板料之间的摩擦，减小凸模圆角与板料之间的摩擦，能够抑制板料的回弹。

The laser composite texture for the surface treatment of U-bend forming was researched. The friction coefficient of different regions on the die surface can be controlled effectively, which can not only improve springback, but also increase the die life. The U-bending was simulated by ABAQUS finite element simulation software. Different friction coefficients were set up in each area of die to reveal the effect of the regional friction on the law of springback of U-bending. Increasing the friction between die corner region, flange surface region and blank，or decreasing the friction between punch corner region and blank can control the springback.

基金项目：

国家自然科学基金资助项目（51175233）；江苏省科技支撑计划资助项目（BE2010060）；江苏省六大人才高峰资助项目（08-B-04)；江苏省科技成果转化专项资金资助项目（BA2010068）；江苏省高校科研成果产业化推进资助项目（JHB2011-39)

参考文献：

[1]Panthi S K,Ramakrishnan N. An analysis of springback in sheet metal bending using finite element method(FEM)[J].Journal of Materials Processing Technology,2007,186(1):120-124.

[2]梁炳文，胡世光.板料成形塑性理论[M].北京：机械工业出版社，1987.

[3]Narkeeran N, Michael L. Predicting springbackin sheet metal forming: an explicit to implicit sequential solution procedure[J]. Finite Elements in Analysis and Design, 1999, 33(1):29-42.

[4]徐丙坤，施法中.板料冲压成形回弹的数值模拟[J].北京航空航天大学学报，2001,27(2):194-197.

[5]Manach P Y,Thuillier S, Menezes L F, et al. Experimental and numerical investigation of springback influence of the work hardening model[A].Yang D Y. Proceedings of Numisheet[C]. Jeju Island,Koreaf，2002.

[6]Ssmuel M. Experimental and numerical prediction of springback and side wall curl in U-bendings of anisotropic sheet metals[J].Journal of Materials Processing Technology,2000,105(3):382-293.

[7]胡兆国.冷冲压工艺及模具设计[M]. 北京：北京理工大学出版社，2009.

[8]孙东成.激光复合造型模具拉延成形性能及回弹的研究[D].镇江：江苏大学，2011.

[9]Naceur H, Guo Y Q. Ben-Elechi S . Response surface methodology for design of sheet forming parameters to control springback effects[J]. Computers and Structures,2006，(84):1651-1663.

[10]施余峰.表面规则微观形貌的激光造型及摩擦学性能的研究[D].镇江：江苏大学，2011.

服务与反馈：

【文章下载】【加入收藏】