网站首页期刊简介编委会过刊目录投稿指南广告合作征订与发行联系我们English
基于Deform的温挤压模具塑性变形失效分析
英文标题:Plastic deformation failure analysis of warm extrusion die based on Deform
作者:栗育琴 张安民 
单位:泸州职业技术学院 
关键词:温挤压 塑性变形 模具失效 模具寿命 有限元模拟 Deform 
分类号:TG376
出版年,卷(期):页码:2011,36(6):141-145
摘要:

生产某壳体零件的凸模存在着严重的塑性变形早期失效现象,本文结合生产实际利用Deform有限元模拟软件对其温挤压过程进行了模拟。通过模拟得到模具在挤压过程中的温度场分布情况。取不同的挤压速度进行了对比分析,得到不同挤压速度时凸模前端高温层厚度。结果表明:当坯料温度低于700 ℃时,凸模因应力超过模具材料的屈服强度发生塑性变形而失效;挤压速度越小,凸模镦粗和局部磨损越严重;模具温度高于400 ℃时,其硬度会随着温度的升高而急剧降低,模具容易塑性变形。

For the die early failure because of plastic deformation, the warm extrusion process of a shell part was simulated using Deform finite element software. Temperature field distribution of mould was acquired. Heat zone thickness of the die front end was acquired with different extruding speeds. The results show that mould plastic deformation will happen because the punch stress exceeds the die material yield strength when blank temperature under 700 ℃. The smaller the extrusion speed, the more serious the punch upsetting and wear.When mould temperature is higher than 400 ℃, the plastic deformation will happen easily beacase of hardness sharply decreasing with temperature increasing.

基金项目:
院级青年基金资助项目(K-1010)
作者简介:
参考文献:

[1]庞祖高, 苏广才, 夏薇,等. 温挤压模具的早期失效探讨及对策[J]. 热加工工艺, 2005, (9): 25-28.

[2]庞祖高, 苏广才, 夏薇,等. 影响温挤压模具的寿命因素及对策探讨[J]. 锻压技术, 2002,27(2): 52-55.

[3]龚红英,朱卉,徐新城,等. 基于Deform-3D的汽车零件冷挤压成形方案研究[J]. 锻压技术, 2009, 34(5): 16-19.

[4]栗育琴, 庞祖高, 周艳霞,等. 温挤压润滑剂的研究[J]. 锻压技术, 2009, 34(2): 110-112.

[5]周艳霞, 庞祖高, 栗育琴,等. 温挤压润滑剂的研究[J]. 锻压技术, 2009, 34(3): 6-9.

[6]胡建军, 许洪斌, 金艳. 塑性成形数值仿真精度的提高途径[J]. 锻压技术, 2009, 34(2): 149-151.

[7]张昌明,张会. 采用Deform 3D对2A12铝合金锻造变形的模拟研究[J]. 锻压技术, 2009, 34(6): 140-142.

[8]蒋鹏,韦韡,余光中,等. 重卡转向节多模膛锻造模具应力的数值模拟[J]. 锻压技术, 2009, 34(4): 151-154.

[9]程培源. 模具寿命与材料[M]. 北京: 机械工业出版社, 1999.

服务与反馈:
本网站尚未开通全文下载服务】【加入收藏
《锻压技术》编辑部版权所有

中国机械工业联合会主管 北京机电研究所有限公司 中国机械工程学会塑性工程分会主办
联系地址:北京市海淀区学清路18号 邮编:100083
电话:+86-010-82415085 传真:+86-010-62920652
E-mail: fst@263.net(稿件) dyjsjournal@163.com(广告)
京ICP备07007000号-9