网站首页期刊简介编委会过刊目录投稿指南广告合作征订与发行联系我们English
QT8812汽车发动机油底壳二次拉深成形回弹分析
英文标题:Springback analysis of QT8812 car engine oil pan by twice deep drawing
作者:覃天 吴泊良 苏广才 胡建华 
单位:桂林理工大学 南宁职业技术学院 广西大学 柳州五顺汽车配件厂 
关键词:发动机油底壳零件 回弹模拟  拉深成形 
分类号:TG386
出版年,卷(期):页码:2013,38(6):178-185
摘要:

利用有限元模拟分析软件ETA/Dynaform对QT8812汽车发动机油底壳进行了二次拉深成形的回弹模拟分析,分别选取油底壳零件切边前后的腰部圆弧部分、深盒部分的截面图进行回弹量变化的分析, 选取这些部位截面上有代表性的特征位置进行相关数据的采集和比较。 结果表明,零件切边前后的回弹量与零件的贴模特性密切相关,拉深阶段贴膜程度越高,塑性变形越充分,零件的回弹量就越小,贴膜程度越低,回弹量就越大。油底壳零件在二次拉深成形切边后的回弹量很低,回弹量的绝对尺寸没有超过允许值2mm。
 

The springback of twice drawing was simulated for QT8812 engine oil-pan by ETA/Dynaform. The circle part of the lumbar and the deep box before and after trimming were analyzed,and the data collected from the typical characteristic location of the above were contrasted. The results show that the springback is associated of the characteristic of attach-die, when the attach-die during the stage of drawing is wore, the plastic deformation is more sufficient and the springback is lower, on the contrary, the springback is larger. The result shows that after twice drawing molding and trimming, the springback is very low,and the absolute size is less than permissible value 2mm. 

基金项目:
作者简介:
参考文献:


[1]龚红英,何丹农,张质良.计算机仿真技术在现代冲压成形过程中的应用[J].锻压技术,2003,28(5):35-38.Gong H Y,He D N,Zhang Z L. Application of computer simulation to modern drawing forming process[J].Forging & Stamping Technology ,2003,28(5):35-38.
[2]李铁.车身覆盖件回弹控制及研究[D].重庆:重庆大学,2006.   Li T. Analysis and Control of Springback of Autobody Penal[D].Qiongqing: Chongqing University, 2006.
[3]任志国,孙振忠.汽车发动机罩板冲压成形及回弹过程的数值模拟[M].北京:化学工业出版社,2008.Ren Z G,Shun Z Z.Numerical Simulation of Forming and Springback Process on Engine-hood[M].Beijing:Chemical Industry Press,2008.
[4]王玥.125摩托车油底壳冲压成形质量控制及成形方案确定[D].成都:西华大学,2010.Wang Y. Stamping Quality Control and Forming Scheme Selection of 125-Motorcyle Oil Pan[D].Chengdu:Xihua University,2010.

服务与反馈:
本网站尚未开通全文下载服务】【加入收藏
《锻压技术》编辑部版权所有

中国机械工业联合会主管 北京机电研究所有限公司 中国机械工程学会塑性工程分会主办
联系地址:北京市海淀区学清路18号 邮编:100083
电话:+86-010-82415085 传真:+86-010-62920652
E-mail: fst@263.net(稿件) dyjsjournal@163.com(广告)
京ICP备07007000号-9