锻压技术

局部偏心形状零件的精密塑性成形技术研究

英文标题：Research on precision plastic forming technology of local eccentric shape part

作者：栾怀超朱建军赵中华徐新成宋震宇

单位：上海工程技术大学

分类号：TG376.5

出版年,卷(期):页码：2014,39(3):104-107

摘要：

局部偏心形状零件结构比较复杂，广泛应用在机械传动中。本文根据该偏心形状零件结构特点，制定了冷温复合精密塑性成形工艺方案。重点设计了偏心冷镦挤预成形工序及温镦挤终成形工序，设计了偏心镦挤和等温镦挤模具，选择了合理的坯料润滑、模具预热及冷却条件，并进行了偏心形状零件的精密塑性成形实验。实验结果表明，采用该工艺及模具可以生产出尺寸精度较高及力学性能优良的偏心形状零件，且材料消耗少、生产效率高，具有较高的经济实用价值。

Eccentric shape parts with complicated structure are widely used in mechanical transmission. A process scheme of cold and warm composite precision plastic forming for the eccentric part was developed according to the structural characteristics of eccentric shape parts. The pre-forming process of eccentric cold extrusion and final forming process of warm upsetting extrusion were mainly designed,and the corresponding precision dies were also designed. Reasonable conditions were selected for blank lubrication, die preheating and cooling. Precision plastic forming experiment for the eccentric shape parts was made. The experimental results indicate that eccentric shape parts with high dimensional accuracy and excellent mechanical properties are produced using this process and dies which has the advantages of low material consumption and high production efficiency and great economic value.

基金项目：

2011年度中央财政085“现代交通运输工程实践训练公共实训平台”(0852011GGPT51)建设项目（B-8932-11-0105；2012年度“上海高校教师产学研践习计划”建设项目（B-8938-12-0636）

参考文献：

［1］赵中华，徐新成，张水忠.地弹簧芯轴冷温复合挤压数值模拟[J].热加工工艺，2007，36（1）：65-68.Zhao Zhonghua, Xu Xincheng，Zhang Shuizhong. Numerical simulation analysis of cold-and-warm composite extrusion technology for spring mandrel [J]. Hot Working Technology, 2007,36(1) :65-68.
［2］孙建，张水忠．基于Deform-3D的离合块冷挤压工艺优化[J].锻压技术，2009,34（5）:12-15.Sun Jian, Zhang Shuizhong. Process optimization of clutch block cold extrusion based on Deform-3D[J]. Forging & Stamping Technology, 2009,34 (5) :12-15
［3］庞祖高，苏广才，夏薇.影响温挤压模具的寿命因素及对策探讨[J].锻压技术，2006,31(2):52-53.Pang Zugao, Su Guangcai, Xia Wei. Discussion of factors influencing warm extrusion die life and countermeasures[J]. Forging & Stamping Technology, 2006,31(2) :52-53.
［4］洪深泽. 挤压工艺及模具设计[M]. 北京：机械工业出版社，1996.Hong Shenze. Extrusion Process and Die Design[M].Beijing: China Machine Press, 1996.
［5］冯文杰，陈莹莹，廖仕利.过轮轴开式冷挤压工艺与模具设计[J].模具工业，2007,33（3）：50-52.Feng Wenjie, Chen Yingying, Liao Shili. Open-type cold extrusion process and die design for spline shaft [J]. Die & Mold Industry, 2007,33 (3):50-52.

服务与反馈：

【文章下载】【加入收藏】