锻压技术

挤压态镍基粉末高温合金热变形行为与组织研究

英文标题：Study on hot deformation behavior and microstructure characteristics of extruded Ni-base powder metallurgy superalloy

作者：王超渊东赟鹏王淑云宋晓俊

单位：北京航空材料研究院

关键词：镍基粉末高温合金热压缩变形本构方程微观组织

分类号：

出版年,卷(期):页码：2014,39(4):126-132

摘要：

通过Gleeble-3500D热力模拟研究了挤压态镍基粉末高温合金在恒温和恒应变速率条件下的热变形行为和组织特征，变形温度范围为950～1150 ℃，应变速率范围为0.001～0.5 s-1。通过线性回归分析，获得了挤压态镍基粉末高温合金的本构方程，并求得热变形激活能为338.638 kJ·mol-1。在1050 ℃以下热压缩变形时，试样容易开裂；而在1050～1150 ℃的温度范围热压缩变形时，试样不易开裂。挤压态镍基粉末高温合金热压缩变形后发生了完全再结晶，再结晶晶粒尺寸受温度影响显著，在低于1100 ℃变形时，再结晶晶粒尺寸随变形温度升高稍有增大；而在高于1100 ℃变形时，再结晶晶粒尺寸随变形温度升高显著增大。该种合金的合理变形参数范围为0.001~0.01 s-1及1050~1100 ℃。

Hot deformation behavior and microstructure characteristics of extruded Ni-base P/M superalloy under constant temperature and strain rate were studied using isothermal compression tests. The compression tests were conducted at 950-1150 ℃ with the strain rate of 0.001-0.5 s-1 on Gleeble-3500D simulator. By regression analysis, the constitutive equation for Ni-base P/M superalloy was developed with hot activation energy of 338.638 kJ·mol-1. The Ni-base P/M superalloy specimens compressed below 1050 ℃ were more likely to crack than that compressed between 1050-1150 ℃.Full dynamical recrystallization occured in all specimens after hot compression deformation, and the recrystallization grain size was significantly affected by temperature.When specimens deformed，with the increasing of temperature，the grain size increased slightly below 1100 ℃, while the grain size increased rapidly above 1100 ℃.The appropriate hot deformation process parameters were strain rate of 0.001-0.01 s-1 and temperature between 1050 and 1100 ℃。

基金项目：

王超渊（1986-），男，硕士，助理工程师

参考文献：

[1]Krueger D D，Kissinger R D，Menzies R G. Development and introduction of a damage tolerant high temperature Nickle-base disk alloy Rene 88 DT[A]. International Symposium on Superalloys Staff Superalloys 1992[C]. USA：Warrendale,1992.

[2]王淑云，李惠曲，张麦仓.FGH96合金等温变形力学性能研究[J].热加工工艺，2002，31（6）：16-18.

Wang Shuyun，Li Huiqu，Zhang Maicang. A study of the mechanical properties of FGH96 alloy in isothermal deformation [J]. Hot Working Technology，2002，31(6)：16-18.

[3]王淑云，张敏聪，东赟鹏，等.FGH96合金热挤压棒材超塑性研究[J].材料工程，2012，（7）：24-28.

Wang Shuyun，Zhang Mincong，Dong Yunpeng，et al. Study on superplasticity of extruded FGH96 alloy[J].Journal of Materials Engineering，2012，(7)：24-28.

[4]刘趁意，王淑云，李付国.粉末高温合金挤压变形组织及变形机理研究[J].锻压装备与制造技术，2009，44(1)：84-87.

Liu Chenyi，Wang Shuyun，Li Fuguo. A study on the microstructure and deformation mechanism during extrusion deformation of powder metallurgy superalloy[J]. China Metal Forming Equipment & Manufacturing Technology，2009，44(1)：84-87.

[5]Richardson G J，Sellars C M，Tegart W J M. Recrystallization during creep of nickel[J]. Acta Metallurgica，1966，14(10)：1225-1236.

[6]Wu Kai，Liu Guo-quan，Hu Beng-fu，et al. Hot compressive deformation behavior of a new isostatically pressed Ni-Cr-Co based powder metallurgy superalloy[J].Materials and Design，2011，32：1872-1879.

[7]马宏.复合合金化AZ31镁合金腐蚀及高温力学性能研究[D].重庆：重庆大学，2010.

Ma Hong.Study on Corrosion and Elevated-temperature Mechanical Properties of AZ31 with Additions Sr and Y[D].Chongqing：Chongqing University，2010.

[8]特日昆.铸造铝基复合材料热挤压行为的研究[D].上海：上海交通大学，2011.

Te Rikun. Research on Hot Extrusion Behavior of Casting Aluminum Matrix Composite[D].Shanghai：Shanghai Jiao Tong University,2011.

[9]Salehi A R，Serajzadeh S，Yazdipour N.A study on flow behavior of A-286 superalloy during hot deformation[J].Materials Chemistry and Physics，2007，101(1)：153-157.

[10]李俊鹏，沈健，许小静，等.7050高强铝合金高温塑性变形的流变行为研究[J].稀有金属，2009，33（3）：318-322.

Li Junpeng，Shen Jian，Xu Xiaojing，et al. Study on the rheological behavior during high temperature deformation of the 7050 high strength aluminum alloy[J].Chinese Journal of Rare Metals，2009，33(3)：318-322.

[11]Xu Wei，Zhang Liwen，Gu Sendong，et al.Hot compressive deformation behavior and microstructure evolution of HIPed FGH96 superalloy[J].Nonferous Met.Soc.China，2012，22：66-71.

[12]刘建涛，张义文，陶宇，等.FGH96合金动态再结晶行为的研究[J].材料热处理学报，2006,27（5）：46-50.

Liu Jiantao，Zhang Yiwen，Tao Yu，et al. Study on the behavior of dynamic recrystallization of FGH96 alloy [J].Transactions of Materials and Heat Treatment，2006，27(5)：46-50.

服务与反馈：

【文章下载】【加入收藏】