锻压技术

基于缺陷控制的DP980高强钢三维变截面辊弯成形有限元仿真

英文标题：Finite element analysis of 3D variable cross-section roll forming for DP980 high strength steel based on defect control

作者：管延智李强王英爽贾方辉陈正阳

单位：内蒙古工业大学

关键词：高强钢变截面辊弯成形成形缺陷有限元分析

分类号：

出版年,卷(期):页码：2014,39(4):137-142

摘要：

三维变截面辊弯成形时，辊组共轭空间曲线扫出空间曲面时仅能控制该曲线上的一点，存在非控制区，因此造成变截面辊弯过程中底部腹板具有“自由变形区”，出现成形缺陷。基于双齿条单齿轮轴系结构的三维变截面辊弯成形装备，提出缺陷控制方法，并基于ABAQUS有限元仿真软件，建立缺陷优化仿真模型。针对DP980双相钢材料进行某汽车构件成形全流程有限元仿真，获得板材成形过程中复杂的变形规律、轧辊成形力与回弹预测。仿真结果表明，缺陷控制方法效果明显，成形件质量较好。通过成形实验进一步验证了缺陷控制的有效性，成形质量与仿真结果基本保持一致。

In the three dimensional variable cross-section roll forming, there exists non-controlled area because the roller group can only control one point on this curve when the conjugate space curve sweeps across space surface, which leading to“free deformation zone” at the bottom of plate in roll bending process，and then forming defects occure. Based on the three dimensional variable cross-section roll forming equipment with double rack single gear shaft structure, the defect control method was put forward, and the defect optimization simulation model was established based on ABAQUS.The whole process simulation of an automobile components forming with DP980 dual phase steel material was done so as to obtain the complex forming rules, roll forming force and springback prediction in sheet metal forming processes. The simulation results show that the effect of defect control method is obvious and the forming quality is better. Through forming experiment, the effectiveness of the defect control was further verified and the forming quality was consistent with the simulation results.

基金项目：

国家科技支撑计划资助项目（2011BAG03B03）

管延智（1981-），男，博士研究生

参考文献：

[1]Ingvarson L. Innovativa stalpriduckter-praktikfall baserad parull forming stekniken[A]. ICIT 2003[C]. Slovenia：Celje, 2003.

[2]Groche P, Ringlera J, Abu Shreehah T. Bending-rolling combinations for strips with optimized cross-section geometries[J]. CIRP Annals-Manufacturing Technology, 2009, 58(1): 263-266.

[3]晏培杰, 韩静涛, 王会凤. 开发中的冷弯成形新技术[J]. 锻压技术, 2012, 37(1): 6-9.

Yan Peijie,Han Jingtao,Wang Huifeng. New technology development of cold roll forming[J].Forging & Stamping Technology,2012,37(1):6-9.

[4]Guan Yanzhi, Li Qiang, Wang Haibo, et al. The development of real time data driving multi-axis linkage and synergic movement control system of 3D variable cross-section roll forming machine[J]. High Technology Letters,2013,19(3):261-266.

[5]Yu Hailiang, Liu Xianghua, Zhao Xianming, et al. Explicit dynamic FEM analysis of multipass vertical-horizontal rolling[J]. Journal of Iron and Steel Research:International, 2006, 13(3): 26-30.

[6]Bao X G, He D N, Lu D, et al. Optimization of autobody panel stamping process based on dynamic explicit finite element method[J]. Acta Metallurgica Sinica:English Letters, 2000, 13(1): 387-393.

[7]Boman R, Papeleux L, Bui Q V, et al. Application of the Arbitrary Lagrangian Eulerian formulation to the numerical simulation of cold roll forming process[J]. Journal of Materials Processing Technology, 2006, 177:621-625.

[8]Salmani Tehrani M, Hartley P, Moslemi Naeini H, et al. Localised edge buckling in cold roll-forming of sysmmetric channel section[J]. Thin-walled Structures, 2006, 44(2):184-196.

[9]尹纪龙, 李大永, 彭颖红, 等. 动力显式有限元法辊弯成形全流程仿真技术研究[J]. 塑性工程学报, 2006, 13(1):36-39.

Yin Jilong,Li Dayong,Peng Yinghong. Whole process simulation of roll forming using dynamic explicit finite element method [J]. Journal of Plasticiy Engineering,2006,13(1):36-39.

[10]曾国, 来新民, 于忠奇, 等. 多道次辊弯成形数值模拟技术[J]. 上海交通大学学报, 2007, 41(10):1598-1602.

Zeng Guo, Lai Xinmin, Yu Zhongqi, et al. The simulaion of roll forming with multiple passes [J]. Journal of Shanghai JiaoTong Univerity,2007,41(10):1598-1602.

[11]李大永, 蒋劲茂, 彭颖红, 等. 辊弯成形过程仿真与参数优化研究[J]. 系统仿真学报, 2007, 19(4):893-896.

Li Dayong,Jiang Jinmao,Peng Yinghong,et al. Study on roll forming process simulation and roll diameters optimization [J]. Journal of System Simulation,2007,19(4):893-896.

[12]曾国, 来新民, 于忠奇, 等. 多道次辊弯成形动力显式仿真的虚拟速度[J]. 上海交通大学学报, 2008, 42(9):1429-1432,1437.

Zeng Guo,Lai Xinmin,Yu Zhongqi,et al. The virtual speed in dynamic explicit FEM simulation for multi-stand roll forming [J]. Journal of Shanghai JiaoTong Univerity,2008,42(9):1429-1432,1437.

服务与反馈：

【文章下载】【加入收藏】