锻压技术

冷锻压力机机身振动特性的模态研究

英文标题：Modal research on vibration characteristics of cold forging press body

作者：杨东祺车卫红徐超

单位：北京机电研究所

分类号：TG315.5

出版年,卷(期):页码：2014,39(5):92-95

摘要：

为更加合理地设计冷锻压力机的机身，使机身抗振、安全、可靠。以北京机电研究所CWFP式12500 kN冷锻压力机为例，首先使用ABAQUS有限元分析软件计算其机身的固有频率，提出几种改进方案，分别进行有限元分析，与原机身的分析结果进行对比，并采用SolidWorks软件画出机身的三维模型。然后再次使用ABAQUS软件对改进方案进行分析，对其影响因素进行了验证与分析。经验证发现，在机身关键部位加筋是影响机身固有频率最重要的因素。

In order to design the body of cold forging press more reasonably and make it be of antivibration, safety and reliability, taking CWFP 12500 kN cold forging press designed by BRIMET as an example, the natural frequency of cold forging press body was calculated by using finite element analysis software ABAQUS firstly.Several improved programs,whose finite element analysis was carried out separately,were put up and compared with analysis result of original body. The 3D model of body was drawn by using SolidWorks. And then,the improved programs, whose affected factors were verified and analyzed, were analyzed by using software ABAQUS again. The verification shows that using reinforcement plate in the key parts of body is the most important factor for affecting the natural frequency of body.

基金项目：

机械科学研究总院技术发展基金“大型多工位冷锻压力机关键技术研究与产品开发”（2009ZX04004-07）

杨东祺（1990-），男，硕士研究生

参考文献：

［1］李建平，王恩福，符起贤，等.高速压力机振动分析与控制[J].机电工程技术，2006，35（6）：56-58.Li Jianping, Wang Enfu, Fu qixian, et al. Analysis and control of the high speed press vibration[J].Mechanical and Electrical Engineering Technology, 2006, 35(6):56-58.
［2］隋晓东，戴挺，高锋. 压力机机身振动特性的模态分析[J].噪声与振动控制，2010，30（1）:10-14．Sui Xiaodong, Dai Ting,Gao Feng. Modal analysis of compressor frames vibration[J]. Noise and Vibration Control, 2010, 30（1）:10-14．
［3］施立军，何彦忠，陈文家. 高速压力机重心位置对机身固有频率的影响研究[J].锻压装备与制造技术，2013，48（1）：22-25．Shi Lijun, He Yanzhong, Chen Wenjia. The influence research of high-speed press gravity position on inherent frequency of frame[J]. China Metal Forming Equipment and Manufacturing Technology, 2013，48（1）：22-25．
［4］张祖芳. 开式压力机机身的有限元分析及其优化设计[D].南京：东南大学，2004.Zhang Zufang. FEM analysis and Optimum Design for Frame of Open-back Press[D].Nanjing: Southwest University, 2004.
［5］周平. 新型压力机机身有限元分析与优化[D].南京：南京理工大学，2007.Zhou Ping. Finite Element Analysis and Optimization of New Press Fame[D].Nanjing: Nanjing University of Science and Technology, 2007.

服务与反馈：

【文章下载】【加入收藏】