锻压技术

基于ABAQUS等效简化模型的辊弯成形机设计分析

英文标题：Design and analysis of roll-forming machine based on ABAQUS equivalent simplified model

作者：陈正阳王海波阎昱贾方辉

单位：北方工业大学

分类号：

出版年,卷(期):页码：2014,39(7):82-86

摘要：

辊弯成形因其高效、节能、节材等特点在许多领域得到广泛应用，而辊弯成形机机构和尺寸设计的合理性对成本和成形精度都有重要影响。将定截面辊弯成形机的模型等效简化，导入到ABAQUS软件中进行板料成形过程的有限元仿真分析，得到与实际生产接近的工作状态下的成形机受力情况，进而对成形机机架中承载的重要零件进行校核分析，并对设计方案的可行性和板料的成形缺陷进行研究。结果表明：数值模拟能为上轴的弹性变形研究和轴承等重要零件的选取提供合理的依据；用螺钉代替调整螺杆承载的方案是可行的；辊弯成形1200 MPa级超高强钢板料时的回弹和纵向弯曲较为明显，需加入过弯和矫正。

Roll forming has been widely used in many fields for its high efficiency, energy-saving, material-saving and other features, and the cost and forming precision are affected greatly by the reasonable design in mechanism and size of roll-forming machine. The model of uniform section roll forming machine was simplified equivalently, then this model was inputted into the ABAQUS for finite element analysis of forming process of sheet metal. The stress distributions of machine under the condition which was close to the actual production situation were obtained, then these important mechanisms of machine that bear load were checked, also the feasibility of design scheme and forming defect of sheet were studied. The results show that the numerical simulation can give a reasonable proof for the elastic deformation research of upper shaft and the selecting of bearings and other important parts; the proposal that using screws instead of stretching screw stem to bear load is feasible; and the 1200 MPa ultrahigh-strength steel sheet has obvious phenomenon of spring back and longitudinal bending during roll forming process, so over bending and rectify should be taken into.

基金项目：

国家自然科学基金资助项目（51205004）

陈正阳（1990-），男，硕士研究生

参考文献：

[1]韩飞，刘继英，艾正青,等. 辊弯成型技术理论及应用研究现状[J]. 塑性工程学报，2010，17(5)：53-60.

Han Fei, Liu Jiying, Ai Zhengqing, et al. State of the art of research on roll forming process [J]. Journal of Plasticity Engineering, 2010, 17(5):53-60.

[2]George T H. 冷弯成型技术手册 [M].刘继英，艾正青，译. 北京：化学工业出版社，2009.

George T H. Roll Forming Handbook [M].Translated by Liu Jiying, Ai Zhengqing. Beijing: Chemical Industry Press, 2009.

[3]Lindgren M. Cold roll forming of a U-channel made of high strength steel[J].Journal of Materials Processing Technology, 2007,186:77-81.

[4]习荣堂，李景方，樊永义.冷弯成型力研究[J].东北大学学报：自然科学版，1996,17（1）：94-98.

Xi Rongtang, Li Jingfang, Fan Yongyi. On cold bend forming force[J]. Journal of Northeastern University：Natural Science, 1996,17（1）：94-98.

[5]曾国，来新民，于忠奇，等.多道次辊弯成形数值模拟技术[J].上海交通大学学报，2007,41（10）：1598-1602.

Zeng Guo, Lai Xinmin, Yu Zhongqi, et al. The simulation of roll forming with multiple passes [J].Journal of Shanghai Jiaotong University, 2007, 41(10): 1598-1602.

[6]赵金龙，刘继英.辊弯弯曲成型方法的有限元仿真研究[J].焊管，2008, 31（5）：29-32.

Zhao Jinlong, Liu Jiying. The finite element simulation study of rolling forming process[J].Welded Pipe and Tube, 2008,31（5）：29-32.

[7]张祎，邹仲平，刘化民.不锈钢波纹板冷弯成形有限元模拟研究[J].锻压技术，2011,36（1）：147-152.

Zhang Yi, Zou Zhongping, Liu Huamin. FEM simulation of cold bending formation laws of stainless steel corrugated plate [J]. Forging & Stamping Technology, 2011,36（1）：147-152.

[8]Bui Q V, Ponthot J P. Numerical simulation of cold roll-forming processes [J]. Journal of Materials Processing Technology, 2008, 202:275-282.

[9]王大勇，傅利斌，李伟，等.U截面型钢压弯回弹的试验研究及预测分析[J].锻压技术，2011,36（1）：140-143.

Wang Dayong, Fu Libin, Li Wei, et al. Test and prediction study of U-section channel in press bending springback process [J]. Forging & Stamping Technology, 2011,36（1）：140-143.

[10]余时建，刘渝，石志云，等. 辊弯成型中的纵向弯曲[J].塑性工程学报，2011, 18（4）：101-105.

Yu Shijian, Liu Yu, Shi Zhiyun, et al. The investigation of longitudinal bending in cold roll forming [J]. Journal of Plasticity Engineering, 2011,18（4）：101-105.

服务与反馈：

【文章下载】【加入收藏】