锻压技术

锻造展宽各经验公式的模拟验证与生产实际的对比分析

英文标题：Comparative analysis between simulated validity of empirical formulas and actual production for forging broadening

作者：龚明亮裴欢欢

关键词：锻造展宽经验公式数值模拟锻坯

分类号：TG386

出版年,卷(期):页码：2014,39(9):6-10

摘要：

利用Deform-3D软件对自由锻展宽拔长进行了大量的有限元数值模拟，根据模拟结果对比分析了7个锻造展宽经验公式的准确性；同时将7个展宽公式与生产实际的下料直径进行比较验证。分析结果表明：数值模拟和生产实际下料直径与各经验公式的计算结果基本一致；公式1的计算结果与展宽拔长初始坯料最小直径最为接近，公式1最贴合生产实际；公式2的计算结果存在局限性且偏差较大；公式3、4、5的计算结果偏差较大；公式6、7的计算结果整体上偏差较小，但当宽高比在小范围内时其计算结果与模拟结果和生产实际比较接近。

The forging broadening process of round bar was numerically simulated by Deform-3D software. The veracity of seven empirical formulas from the forging broadening was comparatively analyzed according to the simulation results, and the actual production was validated and compared at the same time. The results of comparative analysis show that both the simulation results and the actual production are basically in agreement with the calculation results; the calculated value of formula 1 is the closest to the minimum diameter of the initial round bar, and formula 1 is the most consistent with actual production; formula 2 has limits and more deviations to some extent; the calculation results of formulas 3，4，5 have more deviations by comparing the simulation results with the actual production; the calculation results of formulas 6,7 have smaller deviations, while the calculation results and the simulation results are in agreement with the actual production when the ratio of width to high is in a small scale.

基金项目：

龚明亮（1976-），男，硕士，工程师

参考文献：

［1］王德拥，王迪.关于锻造展宽的计算[J].金属加工,2010,7(4):51-54.Wang D Y, Wang D .Calculation about forging broadening[J].Metal Working, 2010,7(4):51-54.
［2］余宗仲.推荐另一个自由锻算料公式[J].锻压技术,1983,8(2):53-55.Yu Z Z. Recommend another empirical formula of raw material calculation of free forging[J]. Forging & Stamping Technology,1983,8(2):53-55.
［3］王有成.推荐一个自由锻算料公式及其曲线图[J].锻压技术,1982,7(3):44-45.Wang Y C . Recommend an empirical formula of raw material calculation of free forging and its graph[J]. Forging & Stamping Technology,1982,7(3):44-45.
［4］胡建军，李小平.Deform-3D塑性成形CAE应用教程[M]. 北京:北京大学出版社,2011.Hu J J,Li X P.CAE Application Course of Deform-3D Plasticity Deformation[M]. Beijing: Beijing University Press,2011.
［5］张振强，辛选荣，刘汀.自由锻拔长效率的研究[J].锻压装备与制造技术,2006(6):50-53.Zhang Z Q,Xin X R,Liu T.Study on stretch efficiency of free forging[J].China Metal Forging Equipment & Manufacturing Technology,2006,(6):50-53.
［6］梁晨，刘助柏.LZ锻造砧宽比、料宽比临界值的研究[J].锻压技术,2004,29(3):14-16.Liang C, Liu Z B. Study on critical value of tool width ratio and blank width ratio of L Z forging[J]. Forging & Stamping Technology,2004,29(3):14-16.
［7］刘助柏，倪利勇，单锐，等.大锻件形变新理论、新工艺及关键技术研究的回顾与展望[J].大型铸锻件,2003,（3）:48-52.Liu Z B,Ni L Y,Shan R,et al. Retrospect & prospect on new theory and new process and key technology of deformation of heavy forgings[J]. Heavy Castings and Forgings,2003,（3）:48-52.

服务与反馈：

【文章下载】【加入收藏】