锻压技术

CAE分析在汽车外板件表面质量提升中的应用

英文标题：Application of CAE in the surface quality improvement for automobile covering parts

单位：烟台工程职业技术学院

分类号：

出版年,卷(期):页码：2014,39(10):146-152

摘要：

使用CAE模拟分析技术对现实生产中车门外板表面质量改进方案进行研究。在某车型前门外板中下部表面折痕问题的整改过程中，通过模拟模型建立生产中的实际生产条件，再现生产中质量缺陷。在模拟过程中验证各改进方案的效果并最终通过进料量、过程缺陷分析、主应变均匀程度、斑马线效果等分析手段对模拟结果进行量化的效果确认，最终得出修改方案。在对实际模具进行改进后，经效果确认，缺陷消除，与分析过程相吻合。应用改进后的方案，较传统的直接修改模具进行验证的方法，更加准确、指导性强。大幅度缩短了修改周期、降低修改成本、提升模具质量。

Using AutoForm software as analysis platform, the improved plans of surface quality for door outer panel were researched. During the improvement on surface crease of middle or low location for automobile front door outer panel, the actual production conditions were simulated by simulation software, and the defect in actual production was reproduced. The effect of improved plans during simulation was quantized and verified by feed, defect analysis of the process, the uniformity of major strain and zebra line effective etc., and the optimal improved plan was obtained at last. After improvement and affect affirmation, the defect was eliminated, and it agreed with the simulation process. Compared with the traditional method of repairing die directly , the improved method was of high accurate and strong guidance，which shortens the period of repair substantially，reduces the repair cost and improves the die quality.

基金项目：

陈娅冰（1978- ），女，硕士，副教授

参考文献：

[1]林忠钦.车身覆盖件冲压成形仿真[M].北京:机械工业出版社,2005.

Lin Z Q. Simulation of Autobody Panel Stamping Simulation[M].Beijing: China Machine Press,2005.

[2]崔令江.汽车覆盖件冲压成形技术[M].北京:机械工业出版社,2003.

Cui L J. Technology of Automobile Panel Stamping Forming[M].Beijing: China Machine Press,2003.

[3]肖景容,姜奎华.冲压工艺学[M]. 北京:机械工业出版社,2004.

Xiao J R, Jiang K H. Stamping Technology [M].Beijing: China Machine Press, 2004.

[4]郑宇锋, 苏传义, 谢文才,等.CAE 分析在产品设计阶段的应用[J].锻压技术, 2012, 37(2): 51-54.

Zheng Y F, Su C Y, Xie W C,et al. Application of CAE in the stage of production design[J]. Forging & Stamping Technology, 2012，37(1):51-54.

[5]冯杨，刘毅，阮锋.板料弯曲的变薄系数[J].锻压技术, 2009,34(3):51-52.

Feng Y,Liu Y,Ruan F. Thinning coefficient of sheet metal bending[J].Forging & Stamping Technology,2009,34(3):51-52.

[6]吕志鹏，马秀花，周思柱.基于ANSYS的阶梯式斜端面组合凹模CAE分析[J]. 锻压技术, 2012, 37(3):114-116.

Lv Z P，Ma X H，Zhou S Z . CAE analysis of staged oblique end combined cavity die based on ANSYS[J]. Forging & Stamping Technology, 2012, 37(1):114-116.

[7]陈永兴. 基于Pro/E的冲压模具组件力学分析[J]. 锻压技术, 2012, 37(2):167-170.

Chen Y X. Mechanical analysis of stamping die components based on Pro/E[J]. Forging & Stamping Technology, 2012, 37(2):167-170.

[8]刘迪辉，吴学胜，张新悦. 一种冲压模具闭合间隙监控方法与实验验证[J].锻压技术,2013,38(3):111-114.

Liu D H，Wu X S，Zhang X Y. Method of stamping dies close gap monitoring and its experimental verification[J]. Forging & Stamping Technology, 2013,38(3):111-114.

服务与反馈：

【文章下载】【加入收藏】