锻压技术

先进高强双相钢拉延回弹实验研究

英文标题：Springback experimental study on stretch bending of advanced high strength dual phase steel

作者：魏星祝洪川潘利波张志建

分类号：TG386.3

出版年,卷(期):页码：2014,39(11):96-101

摘要：

基于企校联合自主研制的拉延弯曲实验机平台，分别研究了武钢590 MPa级和780 MPa级双相钢的拉延弯曲回弹性能。通过不同弯曲半径模拟不同冲压模具圆角半径，同时以不同名义张紧力（0.2~1.2）模拟冲压压边力，分析讨论了两种材料的成形及回弹性能；利用光学应变测量仪分析了两种材料在拉延弯曲区域和弯曲、反弯曲两个区域的应变量。结果表明，同样条件下，780 MPa级双相钢的回弹量要略大于590 MPa双相钢；同时，弯曲半径越大、张紧力越大，两种材料的回弹量和应变越小；反之亦然。

The springback property of stretch bending for WISCO advanced high strength dual phase steel HC590DP and HC780DP was researched based on the stretch bending test equipment designed and manufactured by WISCO and its college copartners. The formability and springback property of two materials were studied by varying the bending radius to simulate the die radius and the nominal tension force（0.2-1.2）to simulate the blank holder force during stamping experiments. In addition, the plastic strain in the typical stretch bending and bending-and-unbending areas of these specimens were measured and analyzed by an optical scanning measurement system. In conclusion, the springback of steel HC780DP with higher strength is larger than that of steel HC590DP under the identical condition. At the same time, the larger the bending radius and tension force, the smaller springback and plastic strain, and vice versa.

基金项目：

湖北省重大科技创新计划项目(2013AAB008)

魏星(1983-),男,硕士,工程师

参考文献：

［1］冯祎卿.双相钢在汽车行业中的应用 [J]. 上海汽车, 2008,(4): 39-42.Feng Y Q. Dual phase steel in automobile [J].Shanghai Automobile, 2008,(4): 39-42.
［2］Jena A K, Chaturvedi M C. On the effect of the volume fraction on martensite on the tensile strength of dual-phase steel [J]. Materials Science and Engineering, 1988, 100: 1-6.
［3］Erdogan M, Tekeli S. The effect of martensite volume fraction and particle size on the tensile properties of a surface-carburized AISI 8620 steel with a dual-phase core microstructure [J]. Materials Characterization, 2002,49(5): 445-454.
［4］Wagoner R H, Li M. Simulation of springback: Through-thickness integration [J]. International Journal of Plasticity, 2007, 23(3): 345-360.
［5］Wagoner R H, Li A. Advances in springback[A]. Proceedings of the 6th International Conference and Workshop on Numerical Simulation of 3D Sheet Metal Forming Processes（Numisheet 2005）[C].Michigan,2005.
［6］Carden W D,Genga L M, Matlock D K, et al. Measurement of springback [J]. International Journal of Mechanical Sciences, 2002，44: 79-101.
［7］Li K P,Carden W P, Wagoner R H. Simulation of springback [J]. International Journal of Mechanical Sciences, 2002,44: 103-122.
［8］Coubrough G J, AlingerM J, Van Tyne C J. Angle of contact between sheet and die during stretch-bend deformation as determined on the bending-under-tension friction test system [J]. Journal of Materials Processing Technology, 2002, 130-131: 69-75.
［9］Marciniak Z, Duncan J L, Hu S J. Mechanics of Sheet Metal Forming [M]. Woburn, MA: Butterworth-Heinemann, 2002.
［10］Wang J F. Principles of the Draw-bend Springback Test [D]. Ann Arbor: The Ohio State University, 2004.

服务与反馈：

【文章下载】【加入收藏】