锻压技术

车用曲轴弯曲镦锻成形工艺模拟及试验研究

英文标题：Simulation and experiment study on upset-bending forging process of crankshaft in automobile

作者：康凤杨鄂川陈强胡传凯沈蕾芳

单位：国防科技工业精密塑性成形技术研究应用中心中国兵器工业第五九研究所重庆理工大学

关键词：曲轴弯曲镦锻有限元金属流线

分类号：TG142.1

出版年,卷(期):页码：2014,39(11):135-138

摘要：

对一种车用曲轴的弯曲镦锻成形工艺难点和解决措施进行了研究。采用有限元模拟方法，直观地再现了曲拐镦挤成形过程中的金属流动情况和容易出现的成形缺陷，研究了飞边厚度和过渡圆角大小对曲拐成形质量的影响，优化出飞边预留厚度为8 mm、曲臂顶部过渡圆角为R5 mm、主轴颈部过渡圆角为R3 mm时，能够获得无缺陷的曲拐。以单拐曲轴为研究对象，开展了曲轴弯曲镦锻成形的工艺试验，验证了模拟结果的准确性，最终制备出的单拐曲轴充型饱满，飞边合理，没有出现塌角、折叠等缺陷，质量完全能够满足技术要求。

For the upset-bending forging process of a kind of crankshaft in automobile, the technical difficulties and solutions were discussed. The metal flowing and the forming defects occurred easily during the upsetting-extruding process of crank, which were simulated intuitively by FEM. Moreover, the influences of thickness of flash and the size of fillet on the forming quality of crank were also analyzed. The parameters were optimized by a flash thickness of 8 mm, top fillet of R5 mm and neck fillet of R3 mm, from which the crank without defects could be obtained. Taking the crankshaft with single crank as an object, the experiment of upset-bending forging process of crankshaft was carried on, which verified the accuracy of simulation results. Finally the crankshaft with single crank was qualified with full deformation and reasonable flash, while without collapsing or folding, and all of the technical requirements can be satisfied.

基金项目：

总装预研基金项目（51318040306）

康凤(1980-)，女，硕士，高级工程师

参考文献：

［1］樊志江,孙丹凤,孙晓鹏,等. NTR法锻造18V48/60曲轴可行性分析[J].大型铸锻件,2009, (5):14-16.Fan Z J, Sun D F, Sun X P,et al. Study on the feasibility of forging 18V48/60 crankshaft by NTR method [J]. Heavy Casting and Forging, 2009, (5):14-16.
［2］徐戊矫,朱若岭,周杰.大型船用曲轴TR法镦锻成形缺陷分析与工艺优化[J].热加工工艺,2010, 39 (7):155-158.Xu W J, Zhu R L, Zhou J. Forming defect analysis and process optimization of heavy marine crankshaft formed by TR upsetting-bending [J]. Hot Working Technology, 2010, 39 (7):155-158.
［3］ Shyoichi Ando. Method for forming a crankshaft: USA, 5115663
［P］.1992-5-26.
［4］孙前江,王高潮,黄映霞,等.曲轴锻造过程的数值模拟[J].锻压技术,2006,31（2）:4-6.Sun Q J, Wang G C, Huang Y X, et al. Numerical simulation of crankshaft in hot forging procedure[J]. Forging & Stamping Technology，2006, 31（2）:4-6.
［5］孙明月, 李殿中, 李依依, 等. 大型船用曲轴曲拐的弯锻过程模拟与实验研究[J]. 金属学报，2005, 41 (12):1261-1266.Sun M Y, Li D Z, Li Y Y, et al. Simulation and experiment study of bending process of large marine crankthrow[J]. Acta Metallurgica Sinica, 2005, 41 (12):1261-1266.
［6］张学忠, 何文武, 刘建生, 等. 大型曲轴弯曲镦锻技术的研究[J]. 机械工程与自动化, 2008, 151 (6):198-200.Zhang X Z, He W W, Liu J S, et al. Development of the bending and upsetting forging method for the integral crankshaft [J]. Mechanical Engineering & Automation, 2008, 151 (6):198-200.

服务与反馈：

【本网站尚未开通全文下载服务】【加入收藏】