锻压技术

薄壁小半径弯头弯胀成形数值模拟技术研究

英文标题：Numerical simulation research on bend-bulge forming of thin-walled elbow with small bending radius

作者：郎利辉罗璇程鹏志訾燕周勇王韬武海

分类号：TG394

出版年,卷(期):页码：2014,39(12):45-52

摘要：

针对现代技术无法直接成形的相对弯曲半径r/D≤1、相对壁厚t/D≤0.05的弯头零件，提出了一种弯胀成形工艺。该工艺将数控弯管技术与充液成形技术相结合，旨在消除传统半管对焊工艺中的焊缝，实现薄壁小半径弯头的整体成形。采用全过程数值分析方法和正交试验方法，研究了弯胀成形工艺的可行性以及关键参数的选取问题。研究结果表明，数控弯管技术使零件的预成形快速且稳定，充液成形技术有效提高了零件的成形极限，弯胀成形工艺对薄壁小半径弯头的制造行之有效。

A Bend-bulge Forming (BBF) process was put forward for elbow parts with relative bending radius r/D≤1 and relative wall thickness t/D≤0.05, which cannot be formed directly with available technologies. BBF combining CNC bending technology and hydroforming technology realizes the forming of thin-walled elbows with small bending radius which eliminates welding lines of traditional half-pipe butt welding process. The feasibility of BBF and selection of key parameters were studied by the numerical simulation of overall process and orthogonal experiment method. The research results show that CNC bending technology is a rapid and stable way for preforming. At the same time, hydroforming technology increases the forming limitation of parts effectively, and BBF is a good method to manufacture thin-walled elbows with small bending radius.

基金项目：

国家自然科学基金资助项目（1175024）

郎利辉（1970-），男，博士，教授;通讯作者：罗璇（1990-），男，硕士

参考文献：

[1]何文治.航空制造工程手册[M].北京：航空工业出版社，1992.

He W Z. Aviation Manufacturing Engineering Handbook[M]. Beijing: Aviation Industry Press, 1992.

[2]程鹏志.导管数控弯曲成形质量预测与工艺优化技术研究[D].北京：北京理工大学，2010.

Cheng P Z. Research on Quality Forecast and Parameters Optimization Technology of NC Tube Bending[D]. Beijing: Beijing Institute of Technology, 2010.

[3]Gao L, Mostch S, Strano M，Classification and analysis of tube hydroforming processes with respect to adaptive FEM simulations[J]. Journal of Materials Processing Technology, 2002，37(5): 22-26.

[4]Prabhu A, Mishra N, Narasimhan N. A study on the effect of pre-bending radius on the formability of hydroformed steel tubes[A]. The 8th International Conference and Workshop on Numerical Simulation of 3D Sheet Metal Forming Processes[C]. Seoul, 2011.

[5]岳永保，杨合，詹梅，等.薄壁管小弯曲半径数控弯曲壁厚减薄实验研究[J].锻压技术，2007，32(5)：58-62.

Yue Y B, Yang H, Zhan M, et al. Experimental study on thinning of thin-walled tube NC bending process with small bending radius[J]. Forging & Stamping Technology, 2007, 32(5): 58-62.

[6]李恒，杨合，詹梅，等.大口径薄壁小弯曲半径数控弯管有限元建模和实验[J].锻压技术，2006，31(5)：136-139.

Li H, Yang H, Zhan M, et al. FEM modeling and experimental of NC bending process of thin-wall tube with large diameter and small bending radius[J]. Forging & Stamping Technology, 2006, 31(5): 136-139.

[7]鄂大辛，宁汝新，唐承统，等.壁厚变形对弯管最小相对弯曲半径的影响[J].锻压技术，2006，31(1)：90-93.

E D X, Ning R X, Tang C T, et al. Influence of wall thickness deformation upon the minimum bending radius of bending tube[J]. Forging & Stamping Technology, 2006, 31(1): 90-93.

[8]苑世剑，刘刚，何祝斌，等.内高压成形机理与关键技术[J].数字制造科学，2008，6(4)：1-34.

Yuan S J, Liu G, He Z B, et al. Mechanism of internal high pressure forming and its key technologies[J]. Digital Manufacture Science, 2008, 6(4): 1-34.

[9]苑世剑.现代液压成形技术[M].北京：国防工业出版社，2009.

Yuan S J. Modern Hydroforming Technology[M]. Beijing: National Defence Industry Press, 2009.

服务与反馈：

【文章下载】【加入收藏】