锻压技术

大型挤压机叠板立柱结构及制造工艺探讨

英文标题：Discussion of laminated plate column structure and manufacturing

作者：张杰斌

单位：太原重工股份有限公司

关键词：叠板立柱挤压机预应力状态

分类号：

出版年,卷(期):页码：2015,40(1):86-89

摘要：

本文介绍的新型挤压机叠板立柱结构，突破了传统圆螺母预紧的圆柱形张力柱结构。通过在挤压机前梁端的大“T”型钩上预加载荷，强制拉长叠板拉杆以后，在前梁与半圆键之间加入垫板，从而建立张力柱的预紧力。分析了叠板立柱的技术要求和制造难点。为了克服长条形板坯变形导致各层叠板的加工和检测尺寸错位，采用在叠板切割下料时两端预留出工艺块，用以安装专用预紧装置，实现叠板拉杆在预应力拉直状态下实施切削加工的方案，从而确保四套叠板立柱与前梁、后梁结合面、半圆键圆弧配合面的等长和一致性，符合设计和装配的精度要求。完善了大型叠板立柱的制造工艺，叠板立柱经过安装检测和用户投产使用，效果良好。

A new type of extrusion press with laminated plate column was introduced, and it made a breakthrough in the traditional round nut tightening structure. The pre-tightening force of tension column was established through preloading on the front end of the beam big “T” hook, and then adding the bolster plate between the beam and woodruff key after laminated rod elongated forcibly. The technical requirements and manufacturing difficulties of laminated plate column were analyzed. In order to overcome dislocations in processing and measuring of laminated plates caused by the rectangular slab deformation, the project of laminated pull rod cutting process under pre-stress straighten state was realized by setting aside processing block for both ends when laminated plate is cut to install special pre-tightening device. Therefore, the isometric and consistency of the four sets of laminated plate columns and combining surface of front and rear beam, and mating surface of woodruff key arc were ensured and met the design and assembling requirements. The manufacturing process of large laminated plate column was improved. It receives a successful result from the laminated plate column after installation, measurement and user feedback.

基金项目：

张杰斌（1975-），男，本科，工程师

参考文献：

［1］郭玉玺，赵国栋.75 MN“短行程”单动卧式铝挤压机[J］.锻压装备与制造技术，2005,40（1）：38-40.Guo Y X，Zhao G D. The 1st “short stroke”-75 MN horizontal single action Al extrusion machine made in china [J］. China Metal Forming Equipment & Manufacturing Technology，2005,40（1）：38-40.

［2］魏军.金属挤压机[M］.北京：化学工业出版社,2006.Wei J. Metal Extrusion Machine[M］. Beijing：Chemical Industry Press,2006.

［3］石如磐，王勇，王丽薇.36 MN预应力结构挤压机机架变形分析[J］.锻压技术，2011，36（4）：100-103.Shi R P，Wang Y，Wang L W. Deformation analysis of 36 MN prestress structure extrusion press frame[J］. Forging & Stamping Technology，2011，36（4）：100-103.\

［4］窦晓玲，孙圣义，郑莉.数控火焰切割工艺的探讨[J］.现代制造技术与装备，2011，（3）：62-63.Dou X L，Sun S Y，Zheng L. Discussion on CNC flame cutting process[J］. China Metal Forming Equipment & Manufacturing Technology，2011，（3）：62-63.

［5］张安顺，隋少春，卢朝琴,等.超大型壁板类零件加工变形控制技术[J］.航空制造技术，2012,（17）：57-59.Zhang A S，Sui S C，Lu Z Q，et al.Giant panel part machining deformation control technology[J］. Aeronautical Manufacturing Technology，2012,（17）：57-59.

［6］朱明，谭建平，周俊峰.125 MN挤压机监控系统设计研究[J］.锻压技术，2008，33（3）：109-111.Zhu M，Tan J P，Zhou J F.Design research on monitoring system of 125 MN extruding machine[J］. Forging & Stamping Technology，2008，33（3）：109-111.

［7］太原重工股份有限公司.大型挤压机叠板立柱的加工液压预紧装置及加工方法：中国，CN 102225539[P］. 2012-12-12.Taiyuan Heavy Industry Co.,Ltd. Processing of hydraulic locking device of large extrusion laminated plate column and processing method：China，CN 102225539[P］. 2012-12-12.

服务与反馈：

【文章下载】【加入收藏】