锻压技术

HFW焊管排辊成形精成形段有限元仿真分析

英文标题：Simulation analysis on fin-forming segment of cage roll-forming for HFW pipes

作者：胡盛德吴晓冬肖颐郭志旺黄英钢

单位：武汉科技大学

分类号：TG376.9

出版年,卷(期):页码：2015,40(3):62-66

摘要：

排辊成形已经被广泛的应用于直缝钢管生产中，由于其成形过程涉及明显的非线性，为研究带钢排辊成形精成形过程，建立了排辊成形机组的大变形弹塑性有限元模型，通过显式动力算法仿真，获得了精成形段带钢的等效塑性应变分布、几何变形规律、边缘纵向应变分布，并进行了实验验证。研究表明，排辊成形精成形段的较大塑性变形发生在带钢中心和边缘；从Fp1至Fp3，PEEQ曲线大致从W状分布向U状分布过渡；边部纵向应变在0.6%以内，未导致边部成形缺陷；几何形状从类U形向顶部开口的规则圆形过渡。

Cage roll-forming has been widely used in pipe production. According to the cage roll-forming process dealing with large nonlinearity, the large deformation elastic finite element model of cage roll-forming mill was established to study the forming process. The distribution of equivalent plastic strain, the regulation of deformed geometry and the longitudinal strain distribution of edge of the strip in the fin-forming were obtained by dynamic explicit algorithm and were verified by measured results. The simulation results show that the bigger equivalent plastic strain occurs in the center and on the edge of the strip in the fin-forming. And from Fp1 to Fp3, the PEEQ curve transforms from W-shaped to U-shaped. The edge longitudinal strain is controlled less than 0.6% and do not lead to edge defects. The geometry shape transforms from an approximate U-shaped to circle with an opening on its top.

基金项目：

钢铁冶金及资源利用省部共建教育部重点实验室开放基金资助项目（FMRU200903)

胡盛德（1972-），男，博士，教授通讯简介：吴晓冬（1987-），男，硕士研究生

参考文献：

［1］于正安，王仕杰，双远华. 板带在排辊成型过程中的仿真研究[J] 山西冶金，2007，30(3)：19-21.Yu Z A, Wang S J, Shuang Y H. Study on FEM simulation of cage roll forming of plate[J]. Shanxi Metallurgy, 2007, 30(3):19-21.
［2］杨仙，张文华，李耀. 冷弯中梁轧辊孔型的计算机辅助设计[J]. 机械设计与制造,2009，(8)：122-124.Yang X, Zhang W H, Li Y. Computer-aided design of roller pass for cold-formed sill[J].Machinery Design & Manufacture, 2009,(8): 122-124.
［3］李大永，罗应兵，张少睿,等. 辊弯成型数值研究综述及全流程仿真关键问题[J]. 机械科学与技术，2004，23(12)：1466-1469.Li D Y, Luo Y B, Zhang S R,et al. Review of numerical research on roll forming and key problems in whole process simulation[J]. Mechanical Science and Technology, 2004, 23(12): 1466-1469.
［4］Bui Q V, Ponthot J P. Numerical simulation of cold roll-forming processes[J]. Journal of Materials Processing Technology, 2008, 202: 275-282.
［5］季晓鹏，张浩，马会文. 国内外大中直径HFW焊管工艺发展研究[J]. 焊管，2009，32(8)：11-15.Ji X P, Zhang H, Ma H W. Discussion on the development and research of the technology of large diameter hi-quality HFW pipe in abroad and domestic[J]. Welded Pipe and Tube, 2009, 32(8): 11-15.
［6］王仕杰，吴云卿，卢星，等. HFW直缝焊管排辊成型轧制力的测试[J]. 焊管，2012，35(8)：43-46.Wang S J, Wu Y Q, Lu X, et al. Rolling force test of HFW longitudinal welded pipe cage roll forming[J]. Welded Pipe and Tube, 2012, 35(8): 43-46.
［7］Kim N, Kang B, Lee S. Prediction and design of edge shape of initial strip for thick tube roll forming using finite element method[J]. Journal of Materials Processing Technology, 2003,(142): 479-486.
［8］谷中莹，李大永，刘玉文,等. ERW焊管排辊成型显式动力有限元仿真线性成型段分析[J]. 塑性工程学报，2008，15(6)：87-90.Gu Z Y, Li D Y, Liu Y W, et al. Analysis on linear forming step of ERW cage roll-forming with explicit FEM simulation[J]. Journal of Plasticity Engineering, 2008, 15(6): 87-90.
［9］蒋劲茂，李大永，彭颖红,等. 直缝焊管排辊成形中预成形段的动力显式仿真[J]. 上海交通大学学报，2008，42(9)：1444-1447.Jiang J M, Li D Y, Peng Y H, et al. Dynamic simulation on pre-forming section of cage roll forming processes of electric resistance welded pipes[J]. Journal of Shanghai Jiao Tong University, 2008, 42(9): 1444-1447.
［10］Jiang J M, Li D Y, Peng Y H, et al. Research on strip deformation in the cage roll-forming process of ERW round pipes[J]. Journal of Materials Processing Technology, 2009,(209): 4850-4856.
［11］Farzin M, Salmani T M, Shameli E. Determination of buckling limit of strain in cold roll forming by the finite element analysis[J]. Journal of Materials Processing Technology, 2002,(125-126): 626-632.

服务与反馈：

【文章下载】【加入收藏】