锻压技术

金属管件电磁脉冲连接特性研究

英文标题：Research on electromagnetic pulse connection characteristics of metal tube

作者：范伟莫健华崔晓辉周波

单位：华中科技大学

分类号：TG391

出版年,卷(期):页码：2015,40(6):43-49

摘要：

采用了带有集磁器结构的电磁脉冲装置对铝合金管与钢管的连接成形进行研究。采用数值模拟和实验相结合的方法探索了集磁器所开缝隙及其宽度对于磁场力分布的影响。对接头处外管均匀性和连接强度的研究结果表明：放电电压越大，接头处外管均匀性越好、连接强度越大；两连接管间间隙越大，接头处外管均匀性越差、连接强度先变大后变小。并应用整体均匀性判据方法获得了既满足均匀性要求又能达到一定连接强度的合理管件间间隙为1.5 mm。

The connection forming of aluminum tube with steel tube was studied by an electromagnetic pulse device with field shaper. The influences of the gap of field shaper and its width on magnetic force distribution were explored by combing numerical simulation with experiment method. The study results show that the large discharge voltage will benefit the uniformity of outer tube connection joint and connection joint strength. The study also shows that the big tube gap leads to poor uniformity of outer tube connection joint with the connection joint strength increasing first and then decreasing. A reasonable tube gap of 1.5 mm, which is satisfied with the requirement of uniformity and certain connection strength, is obtained by the overall uniformity criterion method.

基金项目：

国家自然科学基金资助项目（51175201）

范伟（1990-），男，硕士研究生;通讯作者：莫健华（1952-），男，博士，教授

参考文献：

［1］李春峰.高能率成形技术[M]. 北京：国防工业出版社,2001. Li C F. High Energy Rate Forming Technology[M].Beijing:National Defense Industry Press， 2001.
［2］于海平.基于冲击屈服能量准则的磁脉冲缩径塑性失稳判据[J].塑性工程学报，2008，15（5）：121-126.Yu H P. Plastic buckling condition of magnetic pulse tube compression based on impact buckling energy criterion[J].Journal of Plasticity Engineering，2008，15（5）：121-126.
［3］何文治. 管件电磁缩径成形仿真分析及工艺参数设计[D].武汉：华中科技大学，2011. He W Z. Simulation of Tube Necking Forming and Process Parameters Design[D]. Wuhan： Huazhong University of Science & Technology，2011.
［4］黄霞. 管件电磁成形变形分析及放电能量预测[D]. 哈尔滨：哈尔滨工业大学，2006.Huang X. Deformation Analysis and Discharge Energy Forecast of Tube Electromagnetic Forming[D].Harbin：Harbin Institute of Technology，2006.
［5］赵志学.基于集磁器线圈的3A21铝合金-20号钢管磁脉冲连接研究[D].哈尔滨：哈尔滨工业大学，2011.Zhao Z X. Research on Magnetic Pusle Joining of 3A21 Aluminum-20 Steel Tubes with Field Shaper Assisted Coil[D].Harbin：Harbin Institute of Technology，2011.
［6］范治松. 20号钢/3A21 铝管磁脉冲复合工艺研究[D].哈尔滨：哈尔滨工业大学，2012.Fan Z S. Investigation on Magnetic Pulse Cladding of 3A21 Aluminum-steel 20 Tubes[D].Harbin： Harbin Institute of Technology，2012.
［7］熊海芝，陈亦伟，宋福民，等.磁脉冲压力连接管件的研究[J].锻压技术，1994， 19(6)：31-34.Xiong H Z，Chen Y W，Song F M，et al. Research on connection pipe of magnetic pulse pressure [J]. Forging & Stamping Technology，1994，19(6)：31-34.
［8］卢永进.管件电磁成形均匀性研究[D]．哈尔滨：哈尔滨工业大学，2006.Lu Y J. Research on Uniformity of Tube Electromagnetic Forming[D].Harbin：Harbin Institute of Technology，2006.
［9］崔晓辉.电磁脉冲成形多物理场耦合数值模拟及实验研究[D].武汉：华中科技大学，2013.Cui X H. Multi-physics Field Coupled Simulation and Experimental Study for Electromagnetic Impulse Forming[D]. Wuhan： Huazhong University of Science & Technology，2013.
［10］李胜利，孙维连，葛素静，等.均匀化退火时间对6061铝合金组织和性能的影响[A].材料科学中的数学应用研讨会论文集[C].保定，2010.Li S L，Sun W L，Ge S J，et al. Influence of homogenization annealing time on microstructure of 6061 aluminum alloy[A]. The Mathematics Application Symposium on Materials Science
［C］.Baoding，2010.
［11］Haiping Y，Chunfeng L，Dahai L,et al. Tendency of homogeneous radial deformation during electromagnetic compression of aluminium tube[J]. Transactions of Nonferrous Metals Society of China，Baoding,2010.

服务与反馈：

【文章下载】【加入收藏】