锻压技术

基于Dynaform的叉车轮毂冲压工艺方案改进设计研究

英文标题：Study on improving the design of forklift wheel hub stamping based on Dynaform

作者：胡兆国曹素兵

单位：四川工程职业技术学院

分类号：TH12

出版年,卷(期):页码：2015,40(6):160-164

摘要：

为了减少叉车轮毂的冲压加工工序，尽可能降低生产成本，提出了冲压加工工艺改进措施——在轮毂底部Ф130.5 mm孔的位置上，预冲变形减轻孔Ф80 mm，达到减少一次拉深工序的目的。论证了通过预冲变形减轻孔可以改变圆筒底部受力状态，从而使筒底部金属向筒壁流动，进而增加圆筒高度，减少拉深工序。并应用板料冲压仿真软件Dynaform进行模拟分析验证，结果表明，成形零件未发生起皱和破裂缺陷。同时，生产试验表明，采用改进的冲压工艺可以生产出质量合格的叉车轮毂零件。

In order to reduce the stamping steps and production costs of the forklift wheel hub as much as possible, the improving method of the stamping process was put forward. It was a simplified drawing process with a pre-punching lightening hole of deformation Ф80 mm at the position of Ф130.5 mm on the wheel hub bottom. It was demonstrated that the stress state on the bottom of the cylinder was improved by pre-punching the lightening hole of deformation, which made the metal of the tube bottom flow to tube wall. Therefore the height of the cylinder was increased and the drawing process was reduced. The simulation analysis verification was realized by the sheet metal stamping simulation software Dynaform. The results show that shaped parts are obtained without wrinkling and cracking. At the same time, it is experimental that the improved stamping process can produce the qualified forklift wheel hubs.

基金项目：

胡兆国(1966-),男,硕士,教授

参考文献：

［1］杨关全，框余华. 冷冲压工艺与模具设计[M].大连：大连理工大学出版社，2014.Yang G Q,Kuang Q H. Cold Stamping Process and Mold Design[M]. Dalian: Dalian University of Technology Press,2014.
［2］王秀凤，郎利辉. 板料成形CAE设计及应用——基于Dynaform[M].北京：北京航空航天大学出版社，2010.Wang X F,Lang L H. Sheet Metal Forming CAE Design and Application-based Dynaform[M]. Beijing: Beijing University of Aeronautics and Astronautics Press,2010.
［3］苏建春，于涛. 金属板料成形CAE分析及应用Dynaform工程应用[M].北京：国防工业出版社，2011.Su J C,Yu T. Sheet Metal Forming CAE Analysis and Application Engineering Applications Dynaform[M]. Beijing: Defense Industry Press,2011.
［4］吴梦陵，张珑. 材料成型CAE技术及应用[M]. 北京：电子工业出版社，2011.Wu M L,Zhang L. Material Molding CAE Technology and Applications[M]. Beijing: Electronic Industry Press,2011.
［5］贾敏，白颖，许海燕，等. 钛合金板料橡皮高压冷成形起皱数值模拟与控制研究[J]. 锻压技术，2014,39（6）:132-136.Jia M, Bai Y, Xu H Y,et al. Numerical simulation and control method of wrinkling in rubber high-pressure cold forming of Ti alloy sheet metal[J]. Forging & Stamping Technology,2014,39 (6): 132-136.
［6］王咏梅，李春茂，张瑞萍，等.Pro/Engineer Wildfire 5.0中文版基础教程[M].北京：清华大学出版社，2011.Wang Y M,Li C M,Zhang R P. et al. Chinese Version Pro/engineer Wildfire 5.0 Basic Course[J].Beijing: Tsinghua University Press,2011.

服务与反馈：

【文章下载】【加入收藏】