锻压技术

基于CMM的叶片测点采样分布方法研究

英文标题：Research on CMM-based measuring points sampling and distribution method of blades

作者：张现东卜昆程云勇董一巍

单位：西北工业大学

分类号：TP391

出版年,卷(期):页码：2012,37(4):131-135

摘要：

三坐标测量是复杂叶片外形精度检测的重要手段之一。针对自适应曲率采样、混合采样在大曲率处采样点过密集及在小曲率处过稀疏的缺点，通过优化曲率半径比，并结合叶片的结构特征，提出了一种自适应的分段曲率采样算法，进而对叶片CMM测量点的采样分布进行研究。研究结果表明：在测量点数相同的情况下，与均匀采样和混合采样算法相比，分段曲率采样算法可以使测量点的分布能更好的反映叶片CAD形状，从而提高叶片的三坐标测量效率。

Three-coordinate measuring is one of the most important methods for measuring complex blades. For the mix sampling, the measuring points are too dense in the large curvature area and too sparse in the small curvature area as compared with the adaptive curvature sampling. For this defect, on the basis of the optimization of curvature radius ratio, combining with the structure characteristics of blades, an adaptive sub-curvature sampling algorithm was proposed and established. Compared with uniform sampling and mixed sampling under the same number of measuring points, the distribution of measuring points better reflects the form of CAD by sub-curvature sampling algorithm. So this algorithm can improve the efficiency of measuring complex blades using CMM.

基金项目：

张现东(1986-),男,硕士研究生

参考文献：

［1］Koster M. Curvature-dependent parameterization of curves and surface[J]. Computer-Aised Design,1991,23(8):569-579.
［2］Li S Z. Adaptive sampling and mesh generation[J]. Computer-Aided design,1995,27(3):235-240.
［3］来新民.基于计算机视觉的自由曲面逆向工程关键技术研究[D].天津：天津大学,1997.
［4］Edgeworth R,Wilhelm R G. Adaptive sampling for coordinate metrology[J].Precision Engineering，1999,(23):144-154.
［5］Menq C H, Yau H T, Lai G Y, et al. Automated precision measurement of surface profile in CAD directed inspection [J].IEEE Transactions on Robotics and Automation, 1992, 8(2): 268-278.
［6］Lee G, Mou J, Shen Y. Sampling strategy design for dimensional measurement of geometric features using coordinate measuring machine[J]. Int. J. Mach. Tools Manufacture, 1997,37(7):917-934.
［7］李斌,孙忠林,彭芳瑜,等. 叶片零件在线检测测点规划问题研究[J].中国机械工程,2008,19(5)：540-546.
［8］邹刚,王亚平,李永刚.三坐标测量机测量路径自动生成的研究[J].航空计测技术, 2004,24 (3): 6-7, 21.
［9］解则晓,冯国馨,张国熊.自由曲线曲面测量中的测点布置与准确度[J].计量技术,1999,12(6):21-23.
［10］廖菲,曾韬.基于三坐标测量机的曲面测量规划方法[J].微计算机信息,2010,1(4):152-154.
［11］周保珍.曲面测量方法研究及测量仿真[D].无锡：江南大学,2008.
［12］《航空制造过程手册》总编委会.航空制造工程手册[M].北京：航空工业出版社，1994.
［13］刘杰. 基于典型结构的涡轮叶片收缩率计算方法研究[D].西安:西北工业大学，2008.
［14］龚玉玲,平雪良，周保珍,等.基于矢量相似淘汰算法的CMM测量路径规划及仿真检验[J].工具技术,2008,40(1):114-117.
［15］Su B Q, Liu D Y. Computational Geometry-curve and Surface Modeling[M]. New York:Academic Press,1989.

服务与反馈：

【文章下载】【加入收藏】