锻压技术

双连续弯曲半径铝合金管件推弯成形可行性分析

英文标题：Analysis on push-bending feasibility of aluminum tube with double continuous bending radius

作者：贾震郑岩冰韩志仁刘宝明高铁军

单位：沈阳航空航天大学

分类号：TG335.19

出版年,卷(期):页码：2015,40(8):59-63

摘要：

针对焊接结构降低双连续弯曲半径管件力学性能的缺点，提出利用推弯模具限制成形的特点进行该类管件成形，并对其可行性进行分析。根据单弯曲半径推弯的经验，设计双连续弯曲半径推弯模具型腔，在Forge 3D软件中建立有限元模型，分别模拟有、无内置芯模与管坯端头预倒角的3种工况的成形过程，并对模拟结果进行分析。研究结果表明，芯模和端头预成形分别起到支撑和引导金属流动的作用，两者缺一不可。结合良好工艺条件下的推弯验证试验可得，双连续弯曲半径铝合金管件推弯成形的横截面畸变能够得到有效抑制，该成形方法是可行的。

For the issues of mechanical properties decrease of the weld tube with double continuous bending radius, the push-bending process based on the characteristics of restraint forming by push-bending die was proposed, and its feasibility was analyzed. The die cavity of push-bending with double continuous bending radius was designed according to the experience of push-bending the single bending radius tube. The finite element model (FEM) was established by Forge 3D software, and three working conditions that with the inner mandrel, without the inner mandrel and chamfered end were simulated respectively, and the simulation results were analyzed. The results show that the inner mandrel can support the tube and the chamfered end can guide metal flow, either of which is indispensable. The push-bending test under the good bending conditions is carried out. The cross section distortion of the tube with double continuous bending radius by push-bending can be suppressed effectively, and the forming method is feasible.

基金项目：

国家自然科学基金资助项目(51205260)

贾震（1980-），男，博士，讲师

参考文献：

［1］Kuboki T, Takahashi K, Ono K, et al. A new schedule-free mandrel-less bending method for straight/pre-shaped long tubes [J]. CIRP Annals-Manufacturing Technology, 2013, 62(1): 303-306.
［2］Zhao J, Zhan P, Ma R, et al. Control strategy of over-bending setting round for pipe-end of large pipes by mould press type method[J]. Transactions of Nonferrous Metals Society of China, 2012, 22: 329-334.
［3］Wang X, Song P, Zhao Z, et al. Influence of tube ends constraint on hydro-bending of thin-walled aluminum tube[J]. Transactions of Nonferrous Metals Society of China，2011, 21: 440-444.
［4］Yang H, Li H, Zhang Z, et al. Advances and trends on tube bending forming technologies [J]. Chinese Journal of Aeronautics, 2012, 25(1): 1-12.
［5］朱明清，吉卫喜，张旭，等. 钛T型管液压成形的工艺参数研究[J]. 锻压技术, 2015, 40(1): 56-60.Zhu M Q，Ji W X，Zhang X，et al. Research on technological parameters of hydroforming for titanium T-shaped tube [J]. Forging & Stamping Technology，2015，40（1）：56-60.
［6］李荣兵. ZK60镁合金薄壁矩形管等温挤压仿真研究[J]. 锻压技术, 2013, 38(6): 170-172.Li R B. Numerical study of isothermal extrusion process for ZK60 magnesium alloy thin-wall rectangular tube[J]. Forging & Stamping Technology, 2013, 38 (6): 170-172.
［7］Rouse J P, Leom M Z, Sun W, et al. Steady-state creep peak rupture stresses in 90° power plant pipe bends with manufacture induced cross-section dimension variations[J]. International Journal of Pressure Vessels and Piping, 2013, 105: 1-11.
［8］王修坤，李勇，曾志新，等. 纯滚动式绕弯工艺分析与实验研究[J]. 机械设计与制造, 2012， (5): 141-143.Wang X K, Li Y, Zeng Z X, et al. Process analysis and experimental study on pure riling rotary draw bending [J]. Machinery Design ＆ Manufacture, 2012，(5): 141-143.
［9］刘小锋，杨连发，石松朝. 管材绕弯装置的开发及应用[J]. 金属加工：热加工, 2011, (5): 44-47.Liu X F, Yang L F, Shi S C. Development and application of pipe rotary draw bending device [J]. Metal Working, 2011, (5): 44-47.
［10］Vatter P H, Plettke R. Process model for the design of bent 3-dimensional free-form geometries for the three-roll-push-bending process[J]. Procedia CIRP, 2013, (7): 240-245.
［11］Chang W S, Rajesh S R, Chun C K, et al. Microstructure and mechanical properties of hybrid laser-friction stir welding between AA6061-T6 Al alloy and AZ31 Mg alloy [J]. Journal of Materials Science & Technology, 2011, 27(3): 199-204.
［12］王国振，王春明，王军，等.间隙对5754铝合金激光填丝搭接焊气孔的影响[J]. 中国激光，2012, 39(12): 1203001-1-6.Wang G Z, Wang C M, Wang J, et al. Effects of gap on porosity during laser lap welding with filler wire of Al 5754 sheets[J]. Chinese Journal of Lasers, 2012, 39(12): 1203001-1-6.
［13］王小娜，梁志远，陈科，等.铝合金-镁合金间搅拌摩擦焊异质焊接研究现状[J]. 上海有色金属，2011, 32(1): 32-40.Wang X N, Liang Z Y, Chen K, et al. A review on dissimilar friction-stir welding between aluminum alloys and magnesium alloys[J]. Shanghai Nonferrous Metals, 2011, 32(1): 32-40.

服务与反馈：

【文章下载】【加入收藏】