锻压技术

伺服控制条件下板料拉深性能的研究

英文标题：Research on deep drawing performance of sheet metal under servo control condition

分类号：TG386

出版年,卷(期):页码：2015,40(8):9-12

摘要：

以伺服控制下的板料拉深成形为切入点，开展了速度模式、振荡模式和间歇模式3种典型伺服控制滑块运动模式下的拉深性能研究，给出了各种滑块运动模式对板料拉深成形质量与成形极限的影响。相比于匀速加载，3种滑块运动模式所成形的试样拉深极限高度均有所提高。间歇模式对于杯形件拉深成形改善效果最优，相比匀速加载极限高度提高了10.9%，且间歇时间的适当延长和次数的增多有利于提高材料的塑性变形能力；其次是振荡模式，比匀速成形后的试样极限高度提高了7.5%；最后是速度模式，试样极限高度提高了7.1%。

It was studied the sheet metal drawing performance under three typical servo controlled slide motion modes: speed motion mode, oscillation motion mode and intermittent motion mode, and the influences of various motion modes on forming quality and forming limit were given. Compared with the uniform speed motion, the drawing limit heights of the specimens under the above three slide motion modes were all improved. Among them the intermittent motion mode performed the best with an increase of 10.9% of the drawing limit height, and the plasticity of the material could be further improved by the prolonged intermittent time and increased frequencies. Followed by the oscillation motion mode increased by 7.5%, as a result, the speed motion mode increased by 7.1%.

基金项目：

国家自然科学基金资助项目(51475296)；上海市“曙光”计划（11SG15）

庄新村（1980-），男，博士，副研究员赵震（1972-），男，博士，教授

参考文献：

［1］陈炜，周宏超，徐雪来，等. 盒形件变压边力拉深成形研究[J]. 锻压技术，2014, 39(11): 20-23.Chen W, Zhou H C, Xu X L, et al. Research on variable blank holder force deep drawing for rectangular box parts [J]. Forging & Stamping Technology, 2014, 39(11):20-23.
［2］Yossifon S, Messerly D, Kropp E, et al. A servo motor driven multi-action press for sheet metal forming[J]. International Journal of Machine Tools and Manufacture, 1991, 31(3): 345-359.
［3］渠聚鑫，夏琴香，龙晓斌，等. 伺服压力机主传动及其控制技术的研究进展[J]. 锻压技术，2014, 39(10): 89-97.Qu J X, Xia Q X, Long X B, et al. Research development on the main drive system and control technologies of servo press [J]. Forging & Stamping Technology, 2014, 39(10):89-97.
［4］Otsu M, Yamagata C, Osakada K. Reduction of blanking noise by controlling press motion[J]. CIRP Annals-Manufacturing Technology, 2003, 52(1): 245-248.
［5］Maeno T, Osakada K, Mori K I. Reduction in friction in forging of plates by load oscillation[J]. Journal of the Japan Society for Technology of Plasticity, 2009, 50(585): 951-955.
［6］Maeno T, Osakada K, Mori K. Reduction of friction in compression of plates by load pulsation[J]. International Journal of Machine Tools and Manufacture, 2011, 51(7): 612-617.
［7］叶春生, 侯文杰, 张军伟, 等. 数字伺服压力机控制系统的研究[J]. 锻压技术, 2009, 34(6): 117-121.Ye C S, Hou W J, Zhang J W, et al. Research on control system of numerical crank servo press [J]. Forging & Stamping Technology, 2009, 34(6):117-121.
［8］胡亚民. 氮气弹簧在冲模上的应用[J]. 锻压机械，2001, 36(1): 47-49.Hu Y M. Application of nitrogen-cushion in die [J]. Metalforming Machinery, 2001, 36(1): 47-49.

服务与反馈：

【文章下载】【加入收藏】