锻压技术

保护气氛电渣重熔H13模具钢组织和性能研究

英文标题：Research on microstructure and performance of die steel H13 produced by gas-protective ESR furnace

作者：都影祁孙建林郑亚旭姜方

分类号：TG142.41

出版年,卷(期):页码：2015,40(11):71-76

摘要：

邢台钢铁有限责任公司利用具有保护气氛的抽锭式电渣炉生产Ф600 mm的H13钢锭，并锻造成不同规格的模块。研究了熔速对铸态组织的影响以及锻造工艺对H13钢显微组织和冲击性能的影响。结果表明：在400~550 kg·h-1熔速范围内，钢锭铸态组织中都存在不同程度的枝晶间显微偏析，并有液析碳化物析出。熔速为500 kg·h-1时，铸态组织显微偏析较轻，液析碳化物尺寸较小，且数量较少。在500 kg·h-1熔速下生产的钢锭经不同的锻造工艺变形后发现，只进行单向拔长变形的组织中存在明显的带状偏析，枝晶未被打碎，仍保留了铸态的针状铁素体组织；一镦一拔变形后的组织，铁素体位向逐渐趋于等轴状，碳化物均匀分布程度有提高，但晶界上仍有呈链状析出的碳化物，带状组织未完全消除；三镦三拔多方向反复变形后，枝晶被充分打碎，带状偏析消除，锻后退火组织中的粒状珠光体和碳化物细小均匀，横向冲击韧性明显提高，达到15.5 J·cm-2。

Die steel H13 with diameter of Ф600 mm was produced by gas-protective retracting-type ESR furnace in Xingtai Iron and Steel Corporation, and it was forged into parts of different specifications. The influence of melt rate and forging process on structure and impact toughness of H13 were studied. The results show that when the melt rate is between 400-550 kg·h-1, there are dendrite micro segregation and eutectic carbides in H13 ESR ingot. When the melt rate is up to 500 kg·h-1, dendrite micro segregation is lighter, the size of eutectic carbide in H13 ESR ingot is smaller and its number is less. The ingot which was produced by melt rate 500 kg·h-1 was forged by different processes. The results show that when the ingot is forged by single direction deformation, there are obvious banded structure and casted needle ferrite without broken dendrite; when it is forged by one forging and one pull deformation, the ferrite structure becomes equiaxed shape gradually and distribution of carbides comes more homogeneous. However, chained carbides separates out on the boundary of grain and banded structure is not completely eliminated; when it is forged by three-forging and three-pull multi-direction deformation, dendrite is broken sufficiently, banded structure is eliminated, granular pearlite and carbide are fine and uniform in annealing organization after forging, and the transverse impact toughness is obviously improved up to 15.5 J·cm-2.

基金项目：

国家自然科学基金资助项目（51174020）

都影祁（1975-），男，硕士，高级工程师郑亚旭（1984-），女，硕士，工程师

参考文献：

［1］马党参，周建，张忠佩，等.电渣重熔速度对H13钢组织和冲击性能的影响[J].钢铁，2010，45（8）：80-84.Ma D S, Zhou J, Zhang Z P, et al. Effect of the melting rate of ESR on the microstructure and impact properties of H13 steel [J].Iron and Steel, 2010, 45(8): 80-84.
［2］Zou A Q.Effects of H13 steel microstructure and properties on the service life of heat forging die steel[J].China Mechanical Engineering, 2004, 15(24): 2248-2251.
［3］田玉新，蔡海燕，支玉明，等.影响H13芯棒钢冲击韧性的因素分析[J].宝钢技术，2009，（5）：22-26.Tian Y X, Cai H Y, Zhi Y M, et al. Analysis of factors influencing H13 mandrel steels impact toughness [J].Baosteel Technology, 2009,（5）: 22-26.
［4］李天生，王福明，李长荣，等.含Nb高钼H13钢凝固过程中合金元素的微观偏析[J].特种铸造及有色合金，2013，33（3）：216-219.Li T S, Wang F M, Li C R, et al. Micro segregation of alloying elements in H13 steel with Nb-microalloying and high molybdenum during solidification process[J]. Special Casting & Nonferrous Alloys，2013，33（3）：216-219.
［5］兰杰，贺俊杰，丁文江，等.RE对铸造H13钢凝固组织及冲击韧性的影响[J].钢铁，2000，35（10）：48-50.Lan J, He J J, Ding W J, et al. Influence of RE on solidification structure and impact toughness of cast H13 steel [J]. Iron and Steel, 2000, 35(10): 48-50.
［6］唐文君，吴晓春，闵永安，等.高温均匀化对H13钢强韧性的影响[J].上海金属，2002，24（2）：14-17.Tang W J, Wu X C, Min Y A, et al. Influence of homogenization on the strength and impact toughness of H13 steel [J]. Shanghai Metal, 2002, 24(2): 14-17.
［7］晏广华.H13热作模具钢的组织性能研究[D].合肥：合肥工业大学，2011.Yan G H. Research of Microstructures and Properties of H13 Hot Die Steel [D]. Hefei: Hefei University of Technology, 2011.
［8］ Yan G H, Huang X M, Wang Y Q, et al. Effects of heat treatment on mechanical properties of H13 steel[J].Metal Science and Heat Treatment, 2010, 52(7): 393-395.
［9］ NADCA#207-2003，金相组织评级图片[S].NADCA#207-2003，Heat treatment quality microstructure chart [S].
［10］崔约贤，王长利.金属断口分析[M].哈尔滨：哈尔滨工业大学出版社，1998. Cui Y X, Wang C L. Metal Fracture Analysis [M].Harbin: Harbin Institute of Technology Press, 1998.
［11］霍晓阳.提高H13热作模具钢等向性工艺研究[D].沈阳：东北大学，2005.

Huo X Y. Research on Improving Isotropy of H13 Hot Die Steel[D]. Shenyang: Northeastern University, 2005.

服务与反馈：

【文章下载】【加入收藏】