锻压技术

304L碟形封头冲压回弹研究

英文标题：Research on springback of dished head 304L

单位：1.沈阳理工大学 2.河南神州重型封头有限公司 3. 中国科学院金属研究所

关键词：封头回弹拉深筋弧高仪

分类号：

出版年,卷(期):页码：2016,41(1):43-47

摘要：

利用有限元软件Marc模拟碟形封头的成形过程，提取回弹后各节点的位移，通过UG软件拟合曲线得到封头的回弹量，并与弧高仪测出的封头回弹量对比，证明使用Marc软件模拟封头回弹的可行性。结合正交试验研究了矩形拉深筋各主要几何参数对封头回弹的影响，分析了拉深筋对封头回弹的影响机理，研究结果表明，板料经过拉深筋后产生的加工硬化和残余应力是产生回弹的主要原因，拉深筋的各几何参数对封头的回弹具有决定性作用，其中拉深筋筋高h、拉深筋内圆角R2和凹槽外圆角r1对板料经过拉深筋后的回弹影响较大。

The forming process of dished head was carried out by Marc software, and the displacement of each node was extracted after springback, after that the springback values of the head was obtained from the fitted curves by UG. Comparing with the result measured by the arc height instrument, the feasibility of simulating the springback of the head by Marc was verified. Combined with orthogonal test, the influences of main parameters of the rectangular drawbead on the dished head were researched and the influence mechanism of drawbead on the springback was analyzed. The results show that the residual stress and work hardening of the sheet through the drawbead are the main reason of springback, and the geometric parameters of the drawbead play a decisive role in springback, with the drawbead height h, the fillet draw bead R2 and outside groove fillet r1 greatly impacting the springback of the sheet after the drawbead.

基金项目：

河南省科技开放合作项目（142106000021）

张海龙（1989-)，男，硕士研究生

参考文献：

[1]Johansson B O R,Vitos L,Korzhavyi P A.Chemical composition-elastic property maps of austenitic stainless steels[J].Solid State Sciences，2003,5(6):931-936.

[2]Xue Z,Zhou S,Wei X.Influence of pre-transformed martensite on work-hardening behavior of SUS 304 metastable austenitic stainless steel[J].Journal of Iron and Steel Research,International，2010,17(3):51-55.

[3]Byun T S,Hashimoto N,Farrell K.Temperature dependence of strain hardening and plastic instability behaviors in austenitic stainless steels[J].Acta Materialia，2004,52(13):3889-3899.

[4]王巍,李东升,李小强.铝合金板弯曲回弹试验与有限元仿真[J]. 锻压技术,2013,38（3）:160-164.

Wang W,Li D S,Li X Q.Test and FEM simulation of spingback for aluminum alloy sheet bending[J].Forging & Stamping Technology,2013,38（3）:160-164.

[5]刘迪辉,钟志华.拉延筋对回弹的影响机理研究[J].中国机械工程,2005,16(20):1876-1879.

Liu D H,Zhong Z H.Research on springbck mechanism affected by drawbeads[J].China Mechanical Engineering,2005,16(20):1876-1879.

[6]金淼.方形拉深筋力能特性的数值模拟研究[J]. 燕山大学学报,2001,25(3):209-212.

Jin M.The mechanics characters research of rectangle drawbead by simulation[J].Journal of Yanshan University,2001,25(3):209-212.

[7]华俊杰.可控拉深筋高强度钢板盒形件拉深成形工艺研究[D].重庆：重庆大学,2010.

Hua J J.Deep Drawing Simulation for High-strength Steel Box of Controllable Drawbead[D].Chongqing:Chongqing University,2010.

[8]林策,彭艳,孙建亮,等.板形缺陷板料冲压变形及回弹仿真分析[J]. 锻压技术,2012,37(6):174-178.

Lin C,Peng Y,Sun J L,et al.Stamping deformation and springback simulation analysis of sheet metal with shape defects[J]. Forging & Stamping Technology,2012, 37(6):174-178.

[9]陈帅峰,王守东,雷玉川,等.大型厚壁椭圆封头多次热冲压成形分析[J].锻压技术,2015,40(2):37-40,59.

Chen S F,Wang S D,Lei Y C,et al. Analysis of large thick-wall ellipse head forming by multi-hot stamping[J].Forging & Stamping Technology,2015,40(2):37-40,59.

[10]金淼,郭华英,李志宏.拉深筋对板厚减薄量的影响[J].塑性工程学报,2006,13(3):88-91.

Jin M,Guo H Y,Li Z H.The affect of thickness thinning by the draw bead[J].Journal of Plasticity Engineering,2006,13(3):88-91.

[11]GB/T 25198—2010, 压力容器封头[S].

GB/T 25198—2010, Heads for pressure vessels[S].

服务与反馈：

【文章下载】【加入收藏】