锻压技术

AA5182-O铝合金成形极限确立研究

英文标题：Study on the establishment of forming limit curve of aluminum alloy AA5182-O

作者：吴斌单云

单位：无锡职业技术学院

分类号：TG386

出版年,卷(期):页码：2016,41(3):29-33

摘要：

成形极限曲线作为材料成形性能最为综合和简易的判据，已成为衡量材料成形性和解决冲压成形问题的重要工具。通过对AA5182-O铝合金分别进行了单向拉伸试验、杯突试验、刚模胀形实验，获得了相应方法的成形极限应变点，并将3种方法获得的成形极限拟合曲线进行对比，最后通过实冲实验对实验极限的准确性进行了验证。研究发现，由单向拉伸试验和杯突试验获得的成形极限曲线要低于刚模胀形试验获得成形极限曲线，且杯突试验所得极限点存在等拉极限点，而胀形极限曲线缺少等拉极限点，将实际冲压失效点和实验成形极限曲线相比发现单拉实验和杯突试验获得的成形极限曲线更加准确。

As the most comprehensive and simple criterion of material forming, forming limit curves have become an important tool to measure the formability and solve the stamping problems. The uniaxial tensile test, cupping test and bulging experiments were conducted with aluminum alloy AA5182-O, and the forming limits strain points of corresponding methods were obtained, further the fitted experiment forming limit curves were compared with each other, finally, the stamping was conducted to verify the accuracy of the test forming limit curves. The study shows that the forming limit curves obtained by uniaxial tensile test and cupping test are lower than that by bulging experiments. However, the limit point obtained by cupping test has the equivalent limit point while the bulging limit curve lacks of it. After compared the stamping failure limit points with the experiment forming limit curves, the forming limit curves obtained by the single drawing and cupping tests are more accurate than that by the bulging experiments.

基金项目：

国家自然科学基金资助项目（51165021）;江苏高校品牌专业江苏项目（PPZY2015A086）

吴斌（1972-），男，硕士，副教授

参考文献：

［1］Mori K, Maki S, Tanaka Y. Warm and hot stamping of ultra high tensile strength steel sheets using resistance heating[J]. CIRP Annals-Manufacturing Technology, 2005, 54(1): 209-212.
［2］Bariani P F, Bruschi S,Ghiottia A,et al. Testing formability in the hot stamping of HSS[J]. Manufacturing Technology,2008,57(1): 265-268.
［3］古丽, 张建, 李云涛, 等. 6061铝合金板材冲压成形性能研究[J]. 重型机械, 2009,(2):20-23.Gu L, Zhang J, Li Y T,et al. Research on the property of 6061 alloy sheet drawing[J]. Heavy Machinery, 2009,(2):20-23.
［4］孙成智, 陈关龙, 林忠钦, 等. 控制压边力改善铝合金板成形性能的研究[J]. 材料科学与工艺, 2005, 13(4): 445-448.Sun C Z, Chen G L, Lin Z Q,et al. Control of the blank-holder force to improve the formability of aluminum alloy sheet[J]. Materials Science & Technology, 2005, 13(4): 445-448.
［5］Nargess Sha, Hmanesh Bank. Material advantages[J]. Automotive Engineer,2003, (10) : 38 - 40.
［6］彭晓东, 李玉兰, 刘江. 轻合金在汽车上的应用[J]. 机械工程材料, 1999, 23(2):1-4,23.Peng X D, Li Y L, Liu J. The applications of light alloys to automotive industry[J]. Materials for Mechanical Engineering, 1999, 23 (2):1-4,23.
［7］Bunk W G J. Alumium RS metallurgy[J]. Mater. Sci.Eng.:A,1991, 134:1087-1097.
［8］Lavemia E J ,Ayers J D ,Srivatsan T S. Rapid solidification processing with specific application to aluminum alloys[J ]. Inter. Mater. Rep. ,1991,37(1):1244.
［9］陶友瑞, 吴安如. 耐热铝合金FVS0812 板材冲压成形性能研究[J]. 塑性工程学报, 2008, 15 (3): 9-12. Tao Y R,Wu A R. Research on property of heat-resistance aluminum (FVS0812) sheet drawing[J]. Journal of Plasticity Engineering, 2008, 15 (3): 9-12.
［10］Tetsuo Naka, Gaku Ttorikai, Ryutaro Hino. The effects of temperature and forming speed on the forming limit diagram for type 5083 aluminum-magnesium alloy sheet [J]. Materials Processing Technology, 2001,1(1):648-653.
［11］王巍, 刘春, 李东升. 2024 铝合金筒形件拉深成形试验与有限元仿真[J]. 锻压技术,2014, 39(11):1-5.Wang W, Liu C, Li D S. Cylindrical deep drawing test and finite element simulation of 2024 aluminum alloy sheet[J]. Forging & Stamping Technology, 2014, 39(11):1-5.
［12］陈炜, 周宏超, 徐雪来, 等. 盒形件变压边力拉深成形研究[J]. 锻压技术, 2014, 39(11): 20-23.Chen W, Zhou H C, Xu X L, et al. Research on variable blank holder force deep drawing for rectangular box parts[J]. Forging & Stamping Technology,2014,39(11):20-23.
［13］Bruni C, Forcellese A, Gabrielli F, et al. Effect of temperature, strain rate and fibre orientation on the plastic flow behaviour and formability of AZ31 magnesium alloy[J]. Journal of Materials Processing Technology, 2010,210(10):1354-1363.
［14］杜平梅, 郎利辉, 刘宝胜, 等. 基于M-K模型的成形极限预测及参数影响[J]. 塑性工程学报, 2011, 18(5):84-89.Du P M, Lang L H, Liu B S,et al. Theoretical prediction and parameter influence of FLDs based on M-K mode[J]. Journal of Plasticity Engineering, 2011, 18(5):84-89.

服务与反馈：

【文章下载】【加入收藏】