锻压技术

拉延筋、压边力对冲压件成形性能的影响研究

英文标题：Influences of drawbead and blank holder force on formability of stampings

作者：柯桂颜路平石婧辛秀敏

关键词：拉延筋压边力冲压

分类号：TG386.1

出版年,卷(期):页码：2016,41(5):39-43

摘要：

冲压成形中合理的拉延筋、压边力是减少起皱、拉裂、回弹、拉深不足等的有效措施。以某车型汽车A柱加强板为对象，应用冲压仿真软件Dynaform，研究拉延筋、压边力对冲压件成形质量的影响，详细分析了模面有拉延筋、无拉延筋和不同压边力条件下工件的Z向最大回弹量、最大材料流入量、最大减薄量、最大增厚量和成形极限。分析结果表明：使用拉延筋后，工件的回弹缺陷得到控制，工件的最大增厚率下降，减小了起皱缺陷；压边力对工件成形质量有较大影响，压边力太大工件会出现破裂缺陷，压边力为100 kN是A柱下加强板最优的工艺参数。冲压试验结果与模拟结果吻合较好。

The reasonable choices of drawbead and blank holder force are regarded as an effective method to reduce forming defects such as wrinkling, cracking, springback and insufficiently drawing in the stamping process. For the reinforcing plate of A column in the car, the influences of drawbead and blank holder forces on stamping quality of the workpiece were analyzed by the simulation software Dynaform, and the maximum springback along Z direction, the maximum edge movement of the material, the maximum thinning, the maximum thickening and the forming limit diagram were studied thoroughly under conditions of die surface with drawbead and without drawbead as well as the different blank holder forces. Simulation results show that under the condition of die surface with drawbead, the springback is reduced, the maximum thickening is decreased, and the wrinkling defect is decreased for formed workpiece. Furthermore, blank holder force has great influence on the forming quality of the workpiece, and the workpiece cracks when blank holder force is too large. Blank holder force of 100 kN is regarded as the optimum process parameter to form the reinforcing plate of A column according to the actual production which brings a good agreement with the simulation results.

基金项目：

国家自然科学基金资助项目（51305144）；华侨大学中青年教师科研提升资助计划（ZQN-PY203）；福建省自然科学基金资助项目（2015J01203）；福建省科技计划重点项目（2008H0085）；华侨大学研究生科研创新能力培育计划资助项目

柯桂颜（1992-），男，硕士研究生路平（1980-），女，博士，副教授

参考文献：

［1］史刚.拉延筋技术[J].模具技术，2004,(3): 31-33.Shi G. Drawbeads technology [J]. Die & Mould Technology, 2004,(3): 31-33.
［2］姜奎华.冲压工艺与模具设计[M].北京：机械工业出版社，1998.Jiang K H. Stamping Process and Die Design [M]. Beijing: China Machine Press, 1998.
［3］陈炜，周宏超，徐雪来，等.盒形件变压边力拉深成形研究[J].锻压技术，2014,39(11):20-23.Chen W, Zhou H C, Xu X L, et al. Research on variable blank holder force deep drawing for rectangular box parts [J]. Forging & Stamping Technology,2014,39(11):20-23.
［4］王作成，韩福涛，崔国涛.圆锥形件变压边力拉深工艺的研究[J].塑性工程学报，2006，13(2):25-28.Wang Z C, Han F T, Cui G T. Research on the technology of variable blank holder force drawing for a conical part [J]. Journal of Plasticity Engineering, 2006, 13 (2): 25-28.
［5］Lars G, Erik S. Improving the properties of exterior body panels in automobiles using variable blank holder force [J]. Journal of Materials Processing Technology, 2001, 114:168-173.
［6］Ah metoglu M A, Coremans A, Kinzel C L, et al. Improving raw ability by using variable blank holder force and pressure in deep drawing of round and non-symmetric parts [J]. SAE Transactions, Journal of Materials & Manufacturing, 1993, 102: 428-435.
［7］苏春建，于涛.金属板材成形CAE分析及应用：Dynaform工程应用[M].北京：国防工业出版社，2011.Su C J, Yu T. CAE Analysis and Application of Sheet Metal Forming: Dynaform Engineering Application [M]. Beijing: National Defense Industry Press, 2011.
［8］谢暴.拉延筋设置对汽车覆盖件成形质量的影响[J].机床与液压,2008,36(4):340-344.Xie B. The setting of drawbead in automobile covering parts forming processes [J].Machine Tool & Hydraulics, 2008, 36(4):340-344.
［9］胡丽.轿车左B柱内上板冲压成形模拟研究[D].长春：吉林大学，2015.Hu L. Stamping Simulation Study on the Upper Inner Plate of Automotive Left Column B [D]. Changchun: Jilin University, 2015.
［10］彭必友，殷国富，赵侠,等.板料形状、压料筋的设置对汽车覆盖件成形中起皱和未充分拉深的影响[J].塑性工程学报，2006，13(6):39-43.Peng B Y, Yin G F, Zhao X, et al. Effects of sheet metal forming, compression bar on the wrinkling and insufficient deep drawing in the automobile panel forming [J].Journal of Plasticity Engineering, 2006, 13(6):39-43.

服务与反馈：

【文章下载】【加入收藏】