锻压技术

板料V型弯曲工件端部摆动区域初步研究

英文标题：Preliminary study on swing area in the end of V-shaped bending part

作者：张如华黄智松尹燕徐强

单位：南昌大学

分类号：TG386.3+1

出版年,卷(期):页码：2016,41(10):64-70

摘要：

为避免工件端部与模具或压力机发生干涉，基于变形过程分析和一些假定，列出了忽略模具圆角的板料V型弯曲工件端点轨迹关于工件端部翘起角α的参数方程，证明了轨迹曲线极值坐标相应的端部翘起角αm由模料尺寸比l/L决定，当l/L大时，αm小，反之则大；凹模半角β≤(π/2)-αm，端点轨迹曲线才有极值。给定β和l/L可以决定凹模口外工件摆动区域大小，当l/L大时，区域小，反之则大。通过列方程和作图相结合，分析了在l/L=（0.50~0.30）范围内，增大凹模圆角、增大凸模圆角以及凹模圆角与凸模圆角叠加3种情况下的工件端部摆动区域的变化；给出了接近实际情况的工件中性层端点轨迹方程。最后指出，应视空间宽松程度不同，采取不同方法预留工件端部摆动区域。

In order to avoid the end of workpiece intervening with die or press, the endpoint trajectory parameter equation with camber angel α of V-shaped bending part ignoring the corner radius of die was listed based on analysis of deformation process and some essential assumptions. It is proved that the ratio of die mouth and material length (l/L) determines the value of αm, and the bigger the l/L is, the smaller the αm is, vice versa. When die half-angel β≤(π/2)-αm , the extremum can exist in endpoint trajectory curve. β and l/L also determine the swing area of workpiece out of die, and the bigger the l/L is, the smaller the area is, vice versa. Combining equation and mapping, the change of swing area was discussed in l/L=(0.50-0.30) under three conditions as increasing die corner radius, increasing punch corner radius, or additive effect of die and punch corner radius.The approximate trajectory equation of neutral plane endpoints was given.So the size of swing area in the end of V-shaped bending part should be determined according to the degree of space shortage.

基金项目：

作者简介：张如华（1958-），男，硕士，教授 E-mail：zhangruhua@ncu.edu.cn

参考文献：

[1]聂静静. 数控板料弯曲成形设备研究及有限元分析[D]. 长春：吉林大学，2015.

Nie J J. Research and Finite Element Analysis on CNC Bending Forming Equipment of Sheet Metal[D]. Changchun: Jilin University, 2015.

[2]张如华. 冲压工艺与模具设计[M]. 北京：清华大学出版社，2006.

Zhang R H. Stamping Process and Die Design[M]. Beijing: Tsinghua University Press, 2006.

[3]黄伟，李梦群，杨亚威. 基于Dynaform的V形件弯曲回弹数值模拟[J]. 锻压技术，2014，39（6）：118-121.

Huang W, Li M Q, Yang Y W. Numerical analysis of springback for V-shaped pieces based on Dynaform[J]. Forging & Stamping Technology, 2014, 39(6): 118-121.

[4]李建，赵军，展培培，等. 板料自由弯曲成形及回弹理论解析[J]. 塑性工程学报，2008，16（4）：1-6.

Li J, Zhao J, Zhan P P, et al. Theoretic analysis of forming and springback for sheet metal air bending[J]. Journal of Plastic Engineering, 2008, 16(4): 1-6.

[5]赵军，段璟，马瑞，等. 小曲率平面弯曲弹复方程[J]. 中国科学：技术科学，2011，41（10）：1342-1352.

Zhao J, Duan J, Ma R, et al. Springback equation of small curvature plane bending[J]. Sci. China: Tech. Sci., 2011, 41(10): 1342-1352.

[6]Chan K C, Wang S H. Theoretical analysis of spring back in bending of integrated circuit lead frames[J]. Journal of Materials Processing Technology,1999, 91(1-3): 111-115.

[7]胡丽华，樊新乾. 板料弯曲成形性能有限元模拟研究[J]. 模具工业，2013，39（1）：25-28.

Hu L H, Fan X Q. Finite element simulation study of bending forming performance of sheet metal[J]. Mould Industry, 2013, 39(1): 25-28.

[8]张逸. 金属板料自由折弯模型与实验研究[D]. 武汉：华中科技大学，2012.

Zhang Y. A Thesis Submitted in Partial Fulfillment of the Requirments for the Degree of Master of Engineering[D]. Wuhan: Huazhong University of Science and Technology, 2012.

[9]De Vin, Leo J. Expecting the unexpected, a must for accurate brake forming[J]. Journal of Material Processing Technology, 2001, 117: 244-248.

[10]康海军，余金凤. 板料90°角弯曲展开经验公式[J]. 锻压装备与制造技术，2013，48（4）：65-66.

Kang H J, Yu J F. Empirical formula of 90°angel sheet metal bending[J]. Forging Equipment and Manufacturing Techniques, 2013, 48(4): 65-66.

[11]王孝培. 冲压设计资料[M]. 北京：机械工业出版社，1983.

Wang X P. Stamping Design Data[M]. Beijing: China Machine Press, 1983.

[12]喻平. 数学问题化归理论与方法[D]. 南京：南京师范大学，2002.

Yu P. The Theory and Method of Mathematical Transformation[D]. Nanjing: Nanjing Normal University, 2012.

[13]曾铮，杨之. “化归”刍论[J]. 数学教育学报，2001，10（4）：38-41.

Zeng Z, Yang Z. The hay theory of “Transformation”[J]. Journal of Mathematics Education, 2001, 10(4): 38-41.

服务与反馈：

【文章下载】【加入收藏】