锻压技术

汽车覆盖件拉延模具结构强度计算方法

英文标题：Calculation method of structural strength for automobile panel drawing die

作者：龚志辉刘磊钟剑石建兵

关键词：汽车覆盖件冲压拉延模具结构强度

分类号：TG386.32

出版年,卷(期):页码：2016,41(10):118-121

摘要：

汽车覆盖件模具的结构强度计算是模具结构轻量化设计的重要基础。在分析现有汽车覆盖件拉延模具结构强度计算方法的基础上，提出了一种新的模具结构强度计算方法。该方法将零件的冲压仿真分析分解为刚体冲压和柔体冲压两个过程来进行计算，大部分冲压行程采取刚体冲压以提高效率，在最后成形到底前将模具设置为可变形的柔体继续完成冲压过程。采用该方法对某车门内板零件进行冲压仿真分析，获取了模具的结构强度分析数据。最后采用千分表和摄像机测量模具的实际变形量，并与仿真计算结果进行比对，结果证明仿真计算与实际结果吻合，验证了该方法的有效性。该方法可以有效地提高计算效率，同时又避免了复杂的映射计算，适合工程实际应用需求。

Structural strength calculation of automobile panel dies is an important basis for the lightweight design of die structure. Based on the analysis of the existing methods, a new method to calculate the strength of the die was put forward, which was divided into two parts including rigid body stamping and flexible body stamping to calculate. However, rigid stamping was applied in most of punching strokes to improve calculation efficiency, and in the end the die was set with the flexible body stamping to accomplish the final stamping process. Therefore, the stamping process of a car inner door panel was simulated, and the data of die structure strength were acquired. Furthermore, the actual deformation of the die was measured by dial indicators and camera, and the results were compared with the simulation. The results show that the calculated results are consistent with the actual results, and the effectiveness of method is verified. Therefore, the calculation efficiency can be improved effectively and the complex mapping calculation is avoided to fit in engineering practice.

基金项目：

国家科技重大专项(2014ZX04015051)；国家自然科学基金资助项目(51475155)

作者简介：龚志辉（1974-），男，博士，副教授 E-mail：gzhaa@163.com

参考文献：

[1]谢晖,陈亚柯,潘鑫,等. 冲压成形全过程模拟与回弹补偿研究[J].热加工工艺,2013,42(1):59-62.

Xie H, Chen Y K，Pan X, et al. Research on compensation of springback and simulation based on stamping forming full cycle[J]. Hot Working Technology, 2013,42(1):59-62.

[2]李奇涵, 刘海静, 李笑梅,等. 基于Dynaform的汽车顶盖冲压成形回弹模拟及回弹补偿[J]. 锻压技术, 2015, 40(10):16-19.

Li Q H, Liu H J, Li X M, et al. Springback simulation and compensation of car roof stamping based on Dynaform[J]. Forging & Stamping Technology, 2015, 40(10):16-19.

[3]陈亮. 高强钢冲压模具受力分析有限元模拟与实验研究[D]. 上海：上海交通大学, 2008.

Chen L. Reaearch of Finite Element Modeling & Experiment of Die Structure for High-Strength Steel Stamping[D]. Shanghai: Shanghai Jiao Tong University, 2008.

[4]付春辉. 车身模具强度刚度及疲劳性的有限元分析[D].长春：吉林大学,2007.

Fu C H. The Finite Element Analysis on Strength, Stiffness and Fatigue Character of Automobile Body′s Die[D]. Changchun: Jilin University, 2007.

[5]Lee Y S, Lee J H, Choi J U, et al. Experimental and analytical evaluation for elastic deformation behaviors of cold forging tool[J]. Journal of Materials Processing Technology, 2002, 127(1):73-82.

[6]张贵宝.基于板料成形数值模拟的冲压模具结构分析方法[D].上海：上海交通大学,2008.

Zhang G B. Methodology of Stamping Die Structure Analysis Based on Sheet Metal Forming Numerical Simulation[D]. Shanghai: Shanghai Jiao Tong University, 2008.

[7]Sa C Y, Zhu X H. Integrating metal forming with other performance analyses using a mapping strategy[A]. 2005 SAE World Congress[C]. Detroit, Michigan, 2005.

服务与反馈：

【文章下载】【加入收藏】