锻压技术

接线片塑性成形多工位级进模设计

英文标题：Design of multi-position progressive die for the wiring patch in plastic forming

作者：钟江静梁士红

单位：苏州工业职业技术学院

关键词：接线片弯曲排样级进模弯裂回弹

分类号：TG386

出版年,卷(期):页码：2016,41(9):100-105

摘要：

针对接线片弯曲件易出现的弯裂、回弹、偏移的缺陷，为了找出产生质量问题的主要原因，对精密多工位级

进模具制定合理的冲压工艺和确定合理的模具结构方面做了深入的研究，提出了相应改进措施：对弯曲件的

每个弯曲变形部位采用二次或三次弯曲工艺用以防止弯裂；采用预先对模具工作部分做相应的形状和尺寸修

正等办法控制回弹；使用带弹压装置的导板进行压料防止偏移。分析结果表明，通过采用对应的方法和措施

，保证了接线片的成形精度，延长了精密多工位级进模具的模具寿命。

For the defects of the bending crack, springback, deviation in the wiring patch bent part, the

main reason causing the quality issue was found. A reasonable stamping process and die

structure of multi station progressive die were studied thoroughly, and the corresponding

measures were proposed. Therefore, two or three bending processes were used to prevent from

bending crack, and the methods of pre-modifying the shapes and sizes of

die working portion were used in order to control springback. Furthermore, the workpiece was

pressed by guide board with a suppressing device pressed the work piece to avoid deviation.

The results show that the forming accuracy of the wiring patch is ensured by the corresponding

methods and measures, and the service life of the precision multi station progressive die is

prolonged.

基金项目：

江苏高校品牌专业建设工程（PPZY2015B186）

钟江静（1964-），女，本科，副教授梁士红（1979-），女，硕士，讲师

参考文献：

［1］王鹏驹，成虹.冲压模具设计师手册[M].北京：机械工业出版社，2009.

Wang P J, Cheng H. Stamping Die Design Handbook [M]. Beijing: China Machine Press, 2009.

［2］徐政坤.冲压模具及设备[M].北京：机械工业出版社,2004.

Xu Z K. Stamping Dies and Equipment [M]. Beijing: China Machine Press, 2004.

［3］钟江静. 接触簧片冲压工艺及模具结构的设计[J].锻压技术，2013，38（8）：106-110.

Zhong J J. Optimization design of stamping process and die structure about the contact spring

[J]. Forging & Stamping Technology, 2013，38（8）：106-110.

［4］匡余华. 防火罩多工位成形模具设计[J].锻压技术,2015，40（10）：116-118.

Kuang Y H. Multistage forming die design of fireproof hood[J]. Forging & Stamping Technology, 2015，40（10）：116-118.

［5］柴建国. 3D打印电机定子零件叠加塑性成形级进模具设计[J].锻压技术,2015，40（12）：102-104.

Chai J G. Design of progressive die with superposition plastic forming for 3D printer motor stator core[J]. Forging & Stamping Technology, 2015，40（12）：102-104.

服务与反馈：

【文章下载】【加入收藏】