锻压技术

基于正交试验的汽车引擎盖外板成形工艺参数优化

英文标题：Optimization of forming process parameters for automobile engine cover based on orthogonal experiment

作者：董丽邢同超周淑芳钟佩思

分类号：TG386.1

出版年,卷(期):页码：2016,41(11):62-64

摘要：

对汽车引擎盖外板的成形工艺参数进行研究，借助Dynaform软件对其成形过程进行模拟。基于正交试验方法对压边力、摩擦系数、冲压速度、凸凹模间隙这4个工艺参数进行优化，得出了最佳的成形方案，最终零件的最大变薄率为27.52%，最大变厚率为9.48%。在仿真及正交优化的基础上进行了实际的拉深试模，得出零件的成形性能与有限元模拟结果一致。研究结果表明，基于正交试验法对冲压成形工艺参数优化是可行的，能够缩短产品试模周期，提高成形质量。

The process parameters of automobile engine cover forming were studied, and the forming process was simulated by Dynaform. Then, the blank holder force, friction coefficient, punching speed and the gap between punch and die were optimized, and the optimum forming scheme was given with the maximum thinning rate 27.52% and the maximum thickness rate 9.48%. Furthermore, the actual drawing test was conducted based on simulation and orthogonal optimization, and the forming property was consistent with the finite element modeling results. The research results show that the optimization of stamping process parameters is feasible based on the orthogonal experiment method, and it can shorten the testing period and improve the forming quality of product.

基金项目：

山东省自然科学基金资助项目（ZR2015EM042）

董丽（1983-），女，硕士，讲师

参考文献：

［1］杨俊英, 运新兵, 赵颖, 等. 型腔结构对AZ31镁合金连续挤压扩展成形规律的影响[J]. 稀有金属, 2016, 40(4): 307-314.Yang J Y, Yun X B, Zhao Y, et al. Expansion forming of AZ31 magnesium alloy with two types of cavity structures during continuous extrusion process [J]. Chinese Journal of Rare Metals, 2016, 40(4): 307-314.
［2］高利平, 汪木兰. 基于正交试验的离合器波形片冲压成形工艺参数优化[J]. 锻压技术, 2015, 40(11):32-35.Gao L P, Wang M L. Optimization of stamping process parameters for cushion segment based on orthogonal experiment[J]. Forging & Stamping Technology, 2015, 40(11):32-35.
［3］马国英, 黄彬兵, 苏春建, 等. 汽车翼子板拉深成形模拟及工艺参数优化[J]. 锻压技术, 2015, 40(3):21-24.Ma G Y, Huang B B, Su C J, et al. Simulation and parameters optimization of deep drawing for automobile fender[J]. Forging & Stamping Technology, 2015, 40(3):21-24.
［4］田野, 吕明达, 黄余平. 汽车前门加强板冲压工艺参数优化[J]. 锻压技术, 2014, 39(12):35-38.Tian Y, Lv M D, Huang Y P. Parameter optimization of stamping process on auto front door reinforcing plate[J]. Forging & Stamping Technology, 2014, 39(12):35-38.
［5］曹爱霞, 逯振国, 钟佩思, 等. 基于Dynaform的汽车引擎盖外板拉延成形仿真[J]. 锻压技术，2014，39(12):19-21.Cao A X, Lu Z G, Zhong P S, et al. Simulation of drawing process for automobile engine cover plate based on Dynaform[J]. Forging & Stamping Technology, 2014，39(12):19-21.
［6］苏春建,于涛. 金属板材成形CAE分析及应用—Dynaform工程应用[M]. 北京:国防工业出版社, 2011.Su C J, Yu T. Sheet Metal Forming Analysis and Application of CAE-Dynaform Project Application [M]. Beijing: National Defense Industry Press, 2011.

服务与反馈：

【文章下载】【加入收藏】