锻压技术

汽车板抗凹刚度试验

英文标题：Experimental investigation on dent resistance stiffness for automotive panels

作者：位莉李涛杨瑞枫

分类号：TG386

出版年,卷(期):页码：2016,41(11):121-124

摘要：

针对汽车板的特点，利用IF钢DC04、含磷钢170P1、烘烤硬化钢180BH冲压成形的胀形件及某车型翼子板零件，系统分析了屈服强度、成形条件、烘烤硬化特性等对汽车板抗凹刚度的影响。研究结果表明：高的屈服强度可有效提高汽车板的抗凹刚度，试验中烘烤硬化钢180BH的抗凹刚度最大，170P1次之，DC04的抗凹刚度最小；在合理范围内，可通过增加变形量、增大压边力等工艺手段增加零件的加工硬化程度，从而增大汽车板的抗凹刚度，但零件的抗凹刚度并非随着材料的硬化程度的增加呈线性增强，若增加过量，则引起板料过度变薄，抗凹刚度反而下降；利用烘烤硬化钢板180BH的烘烤硬化特性可显著提高材料的抗凹刚度。

For the characteristics of automotive panels, using bulging parts and automotive fenders produced by IF steel DC04, P-added steel 170P1 and BH steel 180BH, influences of yield strength of steel, forming condition and bake-hardening characteristics on dent resistance stiffness were analyzed systematically. The results show that the dent resistance stiffness can be improved by increasing yield strength of materials, and the dent resistance stiffness of BH steel 180BH reaches the maximum value, steel 170P1 is the second as well as IF steel DC04 is the smallest. Therefore, in a reasonable range, the work hardening of the automobile panel is enhanced by increasing the deformation amount and the blank holder force in order to increase dent resistance stiffness of automotive panel. However, the dent resistance stiffness of automotive panel does not increase linearly with the increase of work hardening. If it is over-increased, sheet material will become too thin, and the dent resistance stiffness of the automotive panel will decrease on the contrary. Thus, the dent resistance stiffness can be improved significantly by the bake-hardening feature of the BH steel 180BH.

基金项目：

位莉（1987-）女，硕士李涛（1977-）男，博士

参考文献：

［1］李东升，周贤宾. 双曲扁壳覆盖件抗凹性的定量评估[J].机械工程学报,1998,34(1)：69-74.Li D S, Zhou X B. Evaluation on sinking resistance of double curvature autobody panels[J].Journal of Mechanical Engineering,1998,34(1)：69-74.
［2］Holmberg S, Thilderkvis P. Influence of material properties and stamping conditions on the stiffness and static dent resistance of automotive panels[J]. Materials and Design, 2002, 23(8):681-691.
［3］龙安，吴青松，祝洪川. 基于Autoform的汽车用钢抗凹性模拟研究[J]. 热加工工艺，2014,43(20):66-68.Long A, Wu Q S, Zhu H C. Research on simulation of dent resistance of automobile steel based on autoform [J]. Hot Working Technology,2014,43(20):66-68.
［4］Ekstranda G, Asnafib N. On testing of the stiffness and dent resistance of auto body panels[J]. Materials and Design, 1998, 19(4): 145-156.
［5］Hua-Chu Shih, Curt D Horvath. Effects of material bending and hardening on dynamic dent resistance[A]. SAE Technical Papers[C]. Detroit, USA, 2005.
［6］张军，黄烜昭，何浪, 等.汽车钢板胀形件刚度和静态残余凹痕抗力试验研究[J]. 锻压技术, 2015,40(5):134-139.Zhang J, Huang X Z, He L, et al. Experimental investigation on the stiffness and static residual dent resistance of automotive steel sheet bulging specimen[J]. Forging & Stamping Technology, 2015,40(5):134-139.
［7］张钧萍,马鸣图,方刚,等. 铝合金板材抗凹性能研究[J].中国工程科学, 2014,16 (1):108-112.Zhang J P, Ma M T, Fang G,et al. Research on dent resistance property of aluminum alloy sheets[J].Engineering Sciences, 2014,16 (1): 108-112.

服务与反馈：

【文章下载】【加入收藏】