锻压技术

SUV车型侧围外板冲压工艺的数值模拟分析

英文标题：Numerical simulation analysis on stamping process of side outer panel for SUV vehicle

作者：关来德

单位：柳州职业技术学院

分类号：TG386

出版年,卷(期):页码：2016,41(12):170-175

摘要：

以某SUV车型侧围外板零件为例，采用Autoform数值模拟软件对侧围外板零件的结构特点和冲压成形工艺进行分析，重点论述了其流水槽区域、门框区域、后保搭接区域和尾灯区域的冲压成形；预测了可能出现的成形缺陷并制定了合理的冲压工艺方案。分析结果表明，侧围外板流水槽区域、门框的A柱部位、尾灯区域存在起皱现象，后门框的圆角部位和后保搭接区域存在开裂风险；采取加大开裂处的模具圆角、调整压边力和改变加强筋长度等措施，对成形工艺进行了优化。试制结果表明，采用优化后的冲压工艺可以有效预防侧围外板零件的起皱、开裂缺陷。

For the side outer panel parts of a SUV vehicle, its structure characteristics and the stamping process were analyzed by Autoform numerical simulation software, and the forming process of the water trough, door frame, rear bumper overlap and tail light areas were discussed in particular. Then, the possible forming defects were predicted, and a reasonable stamping process was confirmed. The analysis results show that the water trough of the side outer panel, the pillar of the door frame and the tail light areas become wrinkling, and the risk of cracking exists at the round corner on the back door frame and rear bumper overlap. Furthermore, the forming process is optimized by enlarging the die corner at the cracking area, adjusting the blank holder force and changing the length of reinforcement rib. The trial production practice proves that wrinkling or cracking can be effectively prevented by the optimized forming process.

基金项目：

基金项目:2014年度广西高校科学技术研究一般资助科研项目（YB2014499）

作者简介：关来德（1977-），男，硕士，讲师 E-mail：529288595@qq.com

参考文献：

［1］何鹏申，王肖英，陈世涛，等. 带双压料机构的侧围外板侧整形模具设计
［J］. 锻压技术，2016,41（4）:89-94.

He P S，Wang X Y，Chen S T,et al.Design on side sizing die of side-frame outer panel with double blank holders
［J］.Forging & Stamping Technology，2016,41(4）:89-94.

［2］杨谊丽，陈文琳，崔礼春. 尾门外板冲压成形数值模拟及伺服拉深实验
［J］. 锻压技术，2016,41(3):153-157.

Yang Y L，Chen W L，Cui L C.Numerical simulation of forming process for tail-gate outer panel and its servo drawing experiment
［J］. Forging & Stamping Technology, 2016，41(3):153-157.

［3］武永甫. 汽车外覆盖件冲压表面畸变预测与模面补偿研究
［J］. 锻压技术，2014,39(12):101-105.

Wu Y F.Research on prediction of stamping surface defects and die surface compensation for automobile exterior panel
［J］.Forging & Stamping Technology，2014,39(12):101-105.

［4］李雪，程迎潮，刘罡，等. 轿车侧围外板冲压成形分析
［J］.锻压技术，2011，36(3): 27-32.

Li X, Cheng Y C, Liu G, et al. Sheet metal stamping analysis of automobile side panel
［J］.Forging & Stamping Technology，2011,36(3): 27-32.

［5］陈燕妮. 侧围外板的成型仿真分析及工艺优化
［J］.专用汽车,2011,(11): 77-79.

Chen Y N. Simulation analysis and process optimization of side outer panel molding
［J］.Special Purpose Vehicle，2011，(11): 77-79.

［6］李用. 汽车左右侧围外板成形方案及斜楔结构设计
［J］.模具制造，2011，(1): 24-31.

Li Y. Stamping forming scheme of the car left-righ side surround plate and wedge structure design
［J］. Die & Mould Manufacture，2011，(1): 24-31.

服务与反馈：

【文章下载】【加入收藏】