锻压技术

汽车变速销模锻成形有限元分析及实验验证

英文标题：Finite element analysis and test verification on mould forging for automobile transmission pin

作者：陈昶熊志宏胡晓华徐畅罗昱沙海

关键词：变速销模锻成形 Deform-3D 模具飞边槽

分类号：TG316.3

出版年,卷(期):页码：2017,42(1):10-14

摘要：

针对汽车变速销的形状、尺寸以及材料性能等特点，选定了单工步开式模锻的成形方法。使用CAE有限元分析软件Deform-3D对初始工艺方案进行仿真研究，分析了材料成形过程中的热、力情况，否定了初始工艺方案的可行性。从坯料尺寸、坯料温度以及模具结构3个方面出发，对成形工艺进行改进，制定了3套改进方案，并通过模拟方法得到较优工艺，即：坯料尺寸为Φ17 mm×47.5 mm，坯料温度为700 ℃，在凹模上增加Φ60 mm×0.2 mm的飞边槽以及在凸模前端设置1个Φ12 mm×0.5 mm的凸起。采用改进后的模具及优化工艺进行实验验证，证明了该工艺的可行性。

For the shape, size and material performance of automobile transmission pin, the single step open mould forging was chosen, and the initial process scheme was simulated by CAE finite element analysis software Deform-3D. Then, thermal and mechanical conditions in the material forming were analyzed, but the feasibility of initial process was denied. From three aspects of billet size, billet temperature and mould structure, three sets of improved forming process were formulated, and a better one was obtained by simulation with billet size of Φ17 mm×47.5 mm, billet temperature of 700 ℃,fash slot of Φ60 mm×0.2 mm on female mould, and protuberance of Φ12 mm×0.5 mm on the front-end of male mould. Furthermore, the improved mould and optimized process were verified by test, and the resibility of the process was proved.

基金项目：

国家自然科学基金资助项目（51475345）

陈昶（1990-），男，硕士，助教 E-mail：chchenenchang@163.com

参考文献：

[1]宋春玉, 李强, 张辉. 基于UG的曲轴模具设计[J]. 机械工程与自动化, 2010, (6): 67-71.

Song C Y, Li Q, Zhang H. Mold design of crankshaft based on UG[J]. Mechanical Engineering & Automation, 2010, (6): 67-71.

[2]吕成, 张立文, 牟正君, 等. 重型燃机叶片锻造过程的三维热力耦合有限元模拟[J]. 塑性工程学报, 2006, 13(4): 54-58.

Lyu C, Zhang L W, Mou Z J, et al. 3D coupled thermal-mechanical FEM simulation of forging process of a gas turbine compressor blade[J]. Journal of Plasticity Engineering, 2006, 13(4): 54-58.

[3]张龙, 孙明月, 李殿中. 高速列车制动盘盘毂锻造工艺数值模拟[J]. 塑性工程学报, 2012, 19(4): 56-61.

Zhang L, Sun M Y, Li D Z. Numerical simulation for die forging of high-speed railway brake disc hub[J]. Journal of Plasticity Engineering, 2012, 19(4): 56-61.

[4]Bramley A N, Mynors D J. The use of forging simulation tools[J]. Materials and Design, 2000, 21 (4): 279-286.

[5]刘永辉, 虞松, 陈军，等. 基于金属刚塑性刚粘塑性不可压缩材料的无网格RKPM法[J]. 塑性工程学报, 2006, 13(5): 1-5.

Liu Y H, Yu S, Chen J, et al. A reproducing kernel particle method based on incompressible rigid-plastic/rigid-viscoplastic materials[J]. Journal of Plasticity Engineering, 2006, 13(5): 1-5.

[6]裴未迟, 张玉强, 孟宪举. 基于Deform轴类零件台阶圆角开式冷挤压工艺有限元模拟[J]. 现代制造工程, 2011，(6): 73-75, 83.

Pei W C, Zhang Y Q, Meng X J. Finite element simulation for shoulder fillet of shaft parts in open-die cold extrusion process based on Deform[J]. Modern Manufacturing Engineering, 2011，(6)：73-75，83.

[7]Nekrasov I I, Karamyshev A P, Parshin V S, et al. Studies of the rolling of ribbed bars using the DEFORM software package[J]. Metallurgist, 2011, 55 (3): 167-170.

[8]潘秀秀, 杨屹, 杨刚, 等. 工作夹片的锻造工艺数值模拟分析 [J]. 锻压技术, 2015, 40(3): 11-15.

Pan X X, Yang Y, Yang G, et al. Numerical simulation and analysis of forging process for the work clamping piece[J]. Forging & Stamping Technology, 2015, 40(3): 11-15.

[9]李晔, 蒋东梅. 新式模锻工艺研究[J]. 装备制造技术, 2013,48(7): 49-51.

Li Y, Jiang D M. New die forging technology research[J]. Equipment Manufacturing Technology, 2013,48(7): 49-51.

[10]付明杰, 张涛, 韩秀全, 等. TNW700 高温钛合金板材超塑变形行为研究[J]. 稀有金属, 2016, 40(1): 1-7.

Fu M J, Zhang T, Han X Q, et al. Superplastic deformation behavior of TNW700 titanium alloy sheet [J]. Chinese Journal of Rare Metals, 2016, 40(1): 1-7.

服务与反馈：

【文章下载】【加入收藏】