锻压技术

方锥件渐进成形扭曲规律及影响因素

英文标题：Distortion regulation and influencing factors of square cone-shaped parts in incremental forming

作者：赵伟林剑豪陈丽

单位：福州大学

分类号：TG386

出版年,卷(期):页码：2017,42(4):68-73

摘要：

渐进成形中，工具头在成形过程中不断推压板料，造成板料产生扭曲变形，影响零件的尺寸精度。为降低零件扭曲程度，提高零件成形精度，以方锥件为例，借助有限元数值模拟，研究渐进成形过程中板料扭曲变形规律，并采用单因素分析法，分析渐进成形各工艺参数对板料扭曲的影响。结果显示，零件底部和侧壁的板料产生了一定程度的扭曲，随着成形深度的增加，扭曲位移最大的位置逐渐向侧壁中部靠近，最终扭曲程度沿侧壁大致呈抛物线分布，且随着工具头半径的减小和层间距的增大，零件扭曲程度加剧。结果表明，通过改变工具头半径和层间距能降低零件扭曲程度，提高零件成形精度。

Because the continued push of the forming tool to the blank in the incremental forming process, the blank was distorted and the dimensional accuracy of parts was affected. To reduce the distortion of parts and improve the forming precision, taking square cone-shaped part for example, the regulation of deformation was studied by means of finite element numerical simulation, and the influences of parameters on distortion were studied by the single factor analysis method. The results show that the bottom and side wall of part are distorted to some extent. With the increase of forming depth, the position of the maximum distortion displacement is close to the middle part,and the distortion occurs parabola distribution along the lateral wall finally. Furthermore, the distortion of parts increases with the decrease of tool radius and the increase of layer spacing. The results show that the distortion of parts can be reduced and the precision can be improved by changing the tool radius and layer spacing.

基金项目：

国家级大学生创新创业训练计划项目（201613470002）；福建省教育厅科技项目（JAT160660）

赵伟(1987-),男,硕士,讲师 E-mail：464228854@qq.com

参考文献：

[1]Emmens W C, Sebastiani G, Boogaard A H. The technology of incremental sheet forming-A brief review of the history[J]. Journal of Materials Processing Technology, 2010, 210(8): 981-997.

[2]Park J J, Kim Y H. Fundamental studies on the incremental sheet metal forming technique[J]. Journal of Materials Processing Technology, 2003, 140(1-3):447-453.

[3]朱虎, 张新迪, 姜在宽, 等. 数控渐进正/反向复合成形中成形顺序对成形质量的影响[J]. 锻压技术, 2016, 41(9): 46-51.

Zhu H, Zhang X D, Kang Jaegwan,et al. Influence of forming sequence on forming quality in positive and negative compound CNC incremental forming[J]. Forging & Stamping Technology, 2016, 41(9): 46-51.

[4]韦红余, 胡铭明. 圆锥形渐进成形制件成形精度研究[J]. 机械工程学报, 2010, 46(9) :193-198.

Wei H Y, Hu M M. Investigation on forming accuracy of cone type sheet metal incremental forming parts[J]. Journal of Mechanical Engineering, 2010, 46(9):193-198.

[5]赵伟, 詹艳然. 基于数值模拟的方锥件渐进成形规律研究[J]. 热加工工艺，2013，42(1): 103-105.

Zhao W, Zhan Y Y. Study on law of incremental forming square cone-shaped parts based on numerical simulation[J]. Hot Working Technology, 2013, 42(1): 103-105.

[6]杨凯程，赵伟，陈丽. 虚拟成形速度对渐进成形数值模拟精度的影响[J]. 锻压技术，2015, 40(2): 103-106.

Yang K C, Zhao W, Chen L. Influence of virtual forming speed on the precision in the numerical simulation of incremental forming[J]. Forging & Stamping Technology, 2015, 40(2): 103-106.

[7]李磊, 周晚林. 金属板料单点渐进成形极限的数值模拟预测[J]. 机械工程学报, 2010, 46(18) : 102-107.

Li L, Zhou W L. Prediction of single point incremental forming limit[J]. Journal of Mechanical Engineering, 2010, 46(18) : 102-107.

服务与反馈：

【文章下载】【加入收藏】