锻压技术

后背门内板成形工艺缺陷分析与优化

英文标题：Analysis and optimization on defects from forming process of back door inner panel

作者：关来德

单位：柳州职业技术学院

分类号：TG386

出版年,卷(期):页码：2017,42(5):19-24

摘要：

以汽车后背门内板为研究对象，根据零件形状起伏变化较大且拉深较深的特点，拟定了4道工序成形工艺方案。利用AutoForm软件对成形工艺方案进行数值模拟，分析拉深过程中零件右上角部位出现的拉裂现象、尾灯附近处存在起皱风险、法兰面有较大回弹量、局部变薄等缺陷，并提出通过加大开裂处R角半径、优化压料面及修改拉延筋减少起皱、在回弹量大的法兰面增加加强筋等措施。结果表明，优化后的后背门内板工艺方案在成形过程中无起皱、开裂缺陷，与数值模拟结果一致，验证了数值模拟分析的正确性。

For the inner plate of the back door, a four-step process was developed based on the characteristics of the large change in parts shapes and the deep drawing. Then, the forming process was simulated by the AutoForm software, and the defects such as crack at the upper right corner of the site, wrinkling near the tail risk, large springback of flange surface and local thinning in the drawing process of parts were analyzed. Furthermore, solutions such as increasing the R corner radius, optimizing and modifying drawbeads to reduce wrinkle and increasing drawbeads on the big flange surface were proposed. The results show that there is no wrinkling and cracking in the forming process of the inner plate of the back door, which is consistent with the numerical simulation results. The correctness of analysis results is proved by the corresponding experiments.

基金项目：

2015年度广西高校科学技术研究项目（KY2015YB401）

关来德（1977-），男，硕士，讲师

参考文献：

［1］肖良红,罗慧娜,向俊仲,等. 基于AutoForm的轿车行李箱内板成形工艺优化[J]. 锻压技术,2014,39（6）:60-64.Xiao L H, Luo H N, Xiang J Z, et al. Forming process optimization for inner panel of car trunk lid based on AutoForm[J].Forging & Stamping Technology,2014, 39（6）:60-64.
［2］杨谊丽，陈文琳，崔礼春. 尾门外板冲压成形数值模拟及伺服拉深实验[J]. 锻压技术，2016,41(3):153-157. Yang Y L，Chen W L，Cui L C. Numerical simulation of forming process for tail-gate outer panel and its servo drawing experiment [J]. Forging & Stamping Technology, 2016，41(3):153-157.
［3］武永甫. 汽车外覆盖件冲压表面畸变预测与模面补偿研究[J]. 锻压技术，2014,39(12):101-105. Wu Y F. Research on prediction of stamping surface defects and die surface compensation for automobile exterior panel[J].Forging & Stamping Technology，2014,39(12):101-105.
［4］常桂静,梁桂荣,曾兵华. 汽车侧围外板成形仿真及工艺优化[J]. 模具工业,2015,41(2):73-76.Chang G J, Liang G R, Zeng B H. Forming simulation and process optimization for automotive side body out panel[J].Die & Mould Industry,2015, 41(2):73-76.
［5］贡见秀,沈左军,孟祥新. 解决侧围外板A柱区域冲压叠料缺陷[J]. 模具技术,2013,(1):35-39. Gong J X, Shen Z J, Meng X X. Solution to stamping wrinkles defects around a pillar area of body side outer [J]. Die and Mould Technology，2013,(1):35-39.
［6］陈淑婉,蒋敏,詹艳然, 等. 汽车行李箱内板拉深过程的数值模拟[J]. 机械设计与制造,2013,(12):267-269,272.Chen S W, Jiang M, Zhan Y R, et al. Numerical simulation of the deep drawing of trunk lid inner panel [J]. Machinery Design & Manufacture, 2013,(12):267-269,272.

服务与反馈：

【文章下载】【加入收藏】