锻压技术

汽车中通道拉延成形工艺参数多目标优化

英文标题：Multi-objective optimization on drawing technological parameters of medium channel part

作者：李雷吴小俊

单位：重庆工业职业技术学院

分类号：TG386.1

出版年,卷(期):页码：2017,42(5):30-33

摘要：

针对某车型中通道零件易出现拉裂和起皱等缺陷，提出通过工艺分析和工艺补充面设计来得到零件的成形工艺流程和工艺补偿面。借助AutoForm软件，建立中通道的拉延成形工序的有限元模型，通过初步模拟，确定以压边力、摩擦系数和拉延筋阻力系数作为试验因素，通过正交试验设计，以优化拉延成形工艺参数。试验中，以最大减薄率和起皱趋势评价函数作为优化的目标函数，并采用多目标优化方法，获得最优的工艺参数组合。实际试模中采用优化后的参数进行试验，得到中通道的产品区域无拉裂和起皱缺陷。

For the defects of medium channel part prone to crack and wrinkle, the forming process and addendum surface were obtained by process analysis and addendum design. Then, the drawing process model was established by the finite element software Autoform, and the blank hold force, friction coefficient and resistance coefficient of drawbeads were chosen as the influence factors after preliminary simulation. Furthermore, an orthogonal test was designed to optimize the drawing process parameters. The maximum thinning rate and wrinkling evaluation function were chosen as the optimized objective functions, and the optimal combination of process parameters was obtained by the multi-objective optimization method. The optimized parameters were used in the die tryout, and the medium channel part without crack and wrinkle defects could be obtained.

基金项目：

重庆市教育科学“十二五”规划2014年度课题（2014-GX-128）；重庆市教委科学技术研究项目（KJ1403005）

李雷（1976-），男，硕士，副教授

参考文献：

［1］严勇,吴超,胡志力，等.汽车铝合金覆盖件成形数值模拟的各向异性屈服准则研究[J].塑性工程学报,2016,23(2):92-97.Yan Y, Wu C, Hu Z L, et al. Anisotropic yield criterion for automotive aluminum panels forming numerical simulation[J].Journal of Plasticity Engineering, 2016,23(2):92-97.
［2］王列亮，郑燕萍，闫盖，等. 基于正交试验的拉延筋阻力优化[J]. 热加工工艺，2014, 43(5): 142-144.Wang L L, Zheng Y P, Yan G, et al. Optimization of drawbead resistance based on orthogonal experiment [J]. Hot Working Technology，2014, 43(5): 142-144.
［3］张渝,丁波,马军伟. 基于正交试验的热冲压冷却过程数值模拟分析[J]. 锻压技术,2015,40(3):105-109.Zhang Y, Ding B, Ma J W. Numerical simulation of hot stamping cooling process based on orthogonal experiment [J]. Forging & Stamping Technology, 2015, 40(3):105-109.
［4］谢晖,罗红专,钟志华. 板料冲压成型CAE中拉裂的预测研究及应用[J]. 湖南大学学报：自然科学版,2005, 32(2):17-20.Xie H, Luo H Z, Zhong Z H. Prediction and application of fractures in CAE of sheet forming [J]. Journal of Hunan University：Natural Sciences,2005, 32(2):17-20.
［5］胡志超,李延平,常勇,等. 基于数值模拟的板料冲压成形回弹补偿方法[J]. 锻压技术,2012,37（2）:163-166.Hu Z C, Li Y P, Chang Y, et al. Compensation algorithm for springback in sheet metal forming based on numerical simulation [J]. Forging & Stamping Technology,2012, 37（2）:163-166.
［6］闫盖,郑燕萍,张文彦,等. 基于正交试验的板料冲压成形工艺参数优化[J]. 热加工工艺,2013,42（17）:94-97.Yan G, Zheng Y P, Zhang W Y, et al. Process parameters optimization of sheet stamping forming based on orthogonal experiment [J]. Hot Working Technology, 2013,42（17）:94-97.
［7］肖红波,蔡浩华. 汽车前翼子板冲压成形工艺优化[J]. 锻压技术,2016,41（2）:35-38.Xiao H B, Cai H H. Improvement of stamping process for car front fender [J]. Forging & Stamping Technology, 2016, 41（2）:35-38.
［8］赵鸿金,李涛涛,杨正斌,等.AZ31镁合金板材轧制过程中边部物理场分布[J].稀有金属,2016,40(10):990-995.Zhao H J, Li T T, Yang Z B, et al. Physical field distribution of AZ31 magnesium alloys plate edge in rolling process[J].Chinese Journal of Rare Metals, 2016,40(10):990-995.

服务与反馈：

【文章下载】【加入收藏】