锻压技术

端面无支撑芯辊模态及其动力响应有限元分析

英文标题：Finite element analysis on modal and dynamic response of unsupported mandrel on end face

作者：袁建波兰箭

分类号：TB115；TG333.91

出版年,卷(期):页码：2017,42(5):152-158

摘要：

利用NX Nastran对轧制矩形截面环件所用的端面无支撑芯辊进行了模态分析数值计算，得到了芯辊约束工况下的前6阶固有频率和模态振型，详细分析了各阶模态振型对芯辊工作状态的影响。简化轧制过程芯辊的受力模型，模拟分析芯辊在3种不同轧制时间作用下的节点位移与应力随时间的变化规律。同时对3种时域轧制力信号进行傅里叶变换，分析轧制力信号的频域组成对芯辊振动的影响。研究表明:芯辊的工作转速远低于其1阶临界转速，轧制过程不会引起芯辊的共振；芯辊的前6阶固有频率处于声波范围内，易造成噪声污染；轧制力相同时，不同轧制时间对芯辊的位移与应力响应无影响；轧制力信号的频域组成不会引起芯辊的共振。

For rolling rectangle section ring, its modal analysis about the end-face unsupported mandrel was carried out by NX Nastran, and natural frequencies and modal vibration shapes of the first six orders were obtained under the constraint condition of the mandrel. Then, the influence of each mode on the working state of the mandrel was analyzed in detail. Furthermore, the force model of the mandrel was simplified in the ring rolling process, and the changes of the mandrel node displacement and stress with time under three kinds of different rolling times were simulated and analyzed. At the same time, rolling force signals from three kinds of time domain were transformed by Fourier transform, and the influence of the frequency domain of the rolling force signals on the mandrel vibration was analyzed. The results show that the working speed of the mandrel is much lower than the first order critical speed, and it can not cause the resonance of the mandrel. The first six-order natural frequencies of the mandrel are in the range of sound wave, which is easy to cause the noise pollution. Under the same rolling force, different rolling periods have few influences on the displacement and stress response of mandrel. The frequency domain components of the rolling force signals can not cause the resonance of the mandrel.

基金项目：

教育部创新团队发展计划项目（IRT13087）

袁建波（1991-），男，硕士研究生兰箭（1972-），男，博士，教授

参考文献：

［1］吕中欢, 汪小凯, 华林，等.油气输送管道法兰环复合轧制过程几何尺寸精度控制方法[J]. 塑性工程学报, 2016, 23(2):35-40.Lyu Z H, Wang X K, Hua L, et al. Control method of geometrical dimension accuracy for flange rings of oil and gas transmission pipeline [J]. Journal of Plasticity Engineering, 2016, 23(2):35-40.
［2］张建华, 彭文飞, 沈法，等. 大口径宽幅薄壁环形件径轴向热辗扩应变场数值分析[J]. 塑性工程学报, 2016, 23(2):41-48.Zhang J H, Peng W F, Shen F, et al. FE analysis of strain filed in radial-axial hot ring rolling of large-diameter, wide-width and thin-wall ring[J]. Journal of Plasticity Engineering, 2016, 23(2):41-48.
［3］俞启灏，黄永铸. 模态分析在工程振动中的应用[J].北京建筑工程学院学报，2007, 23(1):15-18.Yu Q H, Huang Y Z. Application of model test analysis in engineering vibration system [J]. Journal of Beijing Institute of Civil Engineering and Architecture, 2007, 23(1):15-18.
［4］Martin Zahalka. Modal analysis of hydraulic press frames for open die forging [J]. Procedia Engineering, 2014,69 (1) :1070-1075.
［5］邓加东. 复杂深槽环件轧制成形规律与工艺设备设计研究[D].武汉：武汉理工大学出版社，2014. Deng J D. Forming Laws Research and Technology & Equipment Design for Rolling Processing of Complex Deep-groove Ring [D].Wuhan: Wuhan University of Technology,2014.
［6］周敏. 5CrNiMo 热环轧芯辊断裂失效分析[J].锻压技术，2015,40(5):145-148. Zhou M. Failure analysis on the fracture of hot ring-rolling core roller 5CrNiMo [J]. Forging ＆ Stamping Technology, 2015, 40(5):145-148.
［7］华林，贾耿伟，毛华杰. W6M05Cr4V2钢轴承环冷轧芯辊的疲劳断裂与寿命分析[J]. 机械强度,2007, 29(1):156-160. Hua L, Jia G W, Mao H J. Fatigue fracture and life analysis for W6M05Cr4V2 bearing ring cold-rolling mandrel [J]. Journal of Mechanical Strength, 2007, 29(1):156-160.
［8］白化同,郭继忠. 模态分析理论与实验[M].北京：北京理工大学出版社，2001.Bai H T, Guo J Z. Modal Analysis Theory and Experiment [M].Beijing: Beijing Institute of Technology Press, 2001.
［9］曹妍妍,赵登峰. 有限元模态分析理论及其应用[J]. 机械工程与自动化, 2007，(1):73-74.Cao Y Y, Zhao D F. Finite element modal analysis theory and application [J]. Mechanical Engineering & Automation, 2007，(1):73-74.
［10］沈春根，聂文武，裴宏杰，等.UG NX 8.5有限元分析入门与实例精讲[M]. 北京：机械工业出版社，2015.Shen C G, Nie W W, Pei H J, et al. NX UG 8.5 Introduction to Finite Element Analysis and Cases Essence[M]. Beijing: China Machine Press, 2015.
［11］沈春根，王贵成，王树林，等. UG NX 7.0有限元分析入门与实例精讲[M]. 北京：机械工业出版社，2010.Shen C G, Wang G C, Wang S L, et al. NX UG 7.0 Introduction to Finite Element Analysis and Cases Essence[M]. Beijing: China Machine Press,2010.
［12］张珂, 佟俊, 吴玉厚，等. 陶瓷轴承电主轴的模态分析及其动态性能实验[J]. 沈阳建筑大学学报：自然科学版, 2008,24(3):490-493.Zhang K, Tong J, Wu Y H, et al. Model analysis and dynamic characteristic experiment of the ceramic bearing motorized spindle[J]. Journal of Shenyang Construction University：Natural Science Edition, 2008, 24(3):490-493.
［13］吕建法,闫兵,李柏林，等. TX6916镗铣床主轴模态分析及其动态性能试验[J]. 机械设计, 2010, 27(5):45-49.Lyu J F, Yan B, Li B L, et al. Modal analysis and dynamic performance test of TX6916 boring & milling machine spindle [J]. Journal of Machine Design, 2010, 27(5):45-49.
［14］李伟光,王国河. 车铣复合加工中心的铣削动力轴模态分析[J]. 机械设计与制造, 2011，(3):169-171.Li W G, Wang G H. Modal analysis of power-axis milling for turning-milling MC [J]. Machinery Design ＆ Manufacture, 2011，(3):169-171.
［15］潘宏侠，黄晋英.机械工程测试技术[M].北京：国防工业出版社，2009.Pan H X, Huang J Y. Mechanical Engineering Testing Technology [M]. Beijing: National Defense Industry Press, 2009.

服务与反馈：

【文章下载】【加入收藏】