锻压技术

模锻压力机液压系统的设计

英文标题：Design on hydraulic system of die forging press

作者：周鹏

单位：汉江师范学院

分类号：TH137

出版年,卷(期):页码：2017,42(6):117-121

摘要：

根据高强度机械零件的锻压工艺要求，设计了梁柱结构模锻压力机的液压系统和PLC控制系统，液压系统采用了基于增压缸的增压回路，降低了系统的压力等级，提高了液压元件的使用寿命。为实现液压缸的快速运行，系统采用差动连接和基于蓄能器的快速运动回路。为降低液压换向时产生的冲击，采用先降压再换向的泄压回路。利用AMESim软件对增压回路和快速运行回路进行仿真分析，系统压强为10.65 MPa，经过增压回路增压后，液压缸内压强为52.46 MPa，符合增压比5.165的设计要求。仿真结果表明，系统具有压力高、动作快、增压效果明显、自动化程度高等优点，满足高强度机械零件的模锻需求。

According to the forging technology requirements of high strength mechanical parts, the hydraulic system and PLC control system of die forging press with beam-column structure were designed. The hydraulic system applied a booster circuit based on the pressurized cylinder to reduce the pressure rating of system and improve the service life of hydraulic components. Then, it used the differential connection and the accumulator-based fast-motion circuit to achieve the rapid operation of hydraulic cylinder. The relief circuit which decreased pressure first and then changed direction was applied to reduce the impact of hydraulic directional change. Next,the pressure increasing circuit and the fast moving circuit were simulated by AMESim software, and the pressure of system was 10.65 MPa. After the pressure increasing circuit was pressurized, the pressure inside the hydraulic cylinder was up to 52.46 MPa, which accorded with the design requirement of the booster ratio of 5.165. The simulation results show that the system has the advantages of high pressure, quick action, supercharging effect and high automation, and meet the demand for high strength mechanical parts.

基金项目：

汉江师范学院校级教学研究立项项目（2014024）

周鹏（1981-），男，硕士，讲师

参考文献：

［1］居跃峰. 冲压装备自动化技术现状与发展[J].锻压装备与制造技术, 2013,48(1):10-12.

Ju Y F.Status and development of automatic technology for press equipment[J].China Metalforming Equipment ＆ Manufacturing Technology, 2013,48(1):10-12.

［2］魏飞, 张林海, 张斌.挤压式脱水机液压系统的节能改进[J].液压与气动, 2009,(10):68-69.

Wei F, Zhang L H, Zhang B. Development and improvement of energy saving technique for hydraulic system of squeeze-style dehydrator[J].Chinese Hydraulics ＆ Pneumatics,2009,(10):68-69.

［3］凌艳路, 贺小毛, 蒋鹏, 等.63 MN热模锻压力机自动锻造线上模具设计和快换技术应用[J].锻压技术, 2016, 41(6):96-99.

Ling Y L, He X M, Jiang P, et al. Design and quick changing technology of dies for automatic forging production line with hot die forging press of 63 MN[J].Forging ＆ Stamping Technology,2016,41（6）:96-99.

［4］袁清珂, 周鹏, 刘奕华, 等.挤压式织物脱水机的设计与开发[J].机床与液压, 2010, 38(9):54-56,124.

Yuan Q K, Zhou P, Liu Y H, et al. The design and development of squeeze-style fabric dehydrators[J].Machine Tool ＆ Hydraulics,2010,38（9）:54-56,124.

［5］傅新, 徐明, 王伟, 等.锻造操作机液压系统设计与仿真[J].机械工程学报, 2010, 46(11):49-54.

Fu X, Xu M, Wang W, et al. Hydraulic system design and simulation of the forging manipulator[J].Journal of Mechanical Engineering,2010,46（11）:49-54.

［6］刘勇, 邱兆美, 张伏.热冲压成形技术在白车身上的应用[J].拖拉机与农用运输车, 2013, 40(3):67-70.

Liu Y, Qiu Z M, Zhang F. Application of hot stamping technology in body-in-white[J].Tractor ＆ Farm Transporter,2013,40（3）:67-70.

［7］朱立达, 张小丽.YB32-200型压力机液压系统节能设计[J].机床与液压, 2016, 44(20):127-129.

Zhu L D, Zhang X L. Design of energy saving for hydraulic system of YB32-200 press[J].Machine Tool ＆ Hydraulics,2016,44（20）:127-129.

［8］吴怀超, 余云流.YB32-200型四柱万能液压机PLC控制系统的开发[J].液压与气动, 2011, (2):56-58.

Wu H C, Yu Y L. Development of PLC control system for YB32-200 four-column universal hydraulic press[J]. Chinese Hydraulics ＆ Pneumatics,2011,(2): 56-58.

［9］裴华军, 马国礼, 崔礼春. HSHP-1000T液压机节能效应浅析[J].锻压技术, 2013, 38(5):142-144.

Pei H J, Ma G L, Cui L C. Analysis of energy saving effect in HSHP-100T hydraulic press[J].Forging ＆ Stamping Technology,2013,38(5):142-144.

［10］代平之, 张作龙.液压泵回路的节能措施[J].流体传动与控制, 2007, 14(1):51-55.

Dai P Z, Zhang Z L. An analysis of energy-saving of the hydraulic pump circuit[J].Fluid Power Transmission & Control,2007, 14(1):51-55.

［11］王文红, 顾卫彬.PLC和触摸屏在多工位冷锻成形机中的应用[J].锻压技术, 2012, 37(1):105-109.

Wang W H, Gu W B. Application of PLC and touch screen in multi-station cold forming machine[J]. Forging ＆ Stamping Technology,2012,37（1）:105-109.

服务与反馈：

【文章下载】【加入收藏】