锻压技术

连接件级进模排样及模具结构设计

英文标题：Layout and structure design on progressive die for connector

作者：闫华军臧其其刘玉忠张双杰

关键词：连接件级进模排样模具结构冲压

分类号：TG386.2

出版年,卷(期):页码：2017,42(7):107-112

摘要：

针对某连接件进行了冲压工艺分析，通过比较两种排样方法，最终优化设计了由5个冲裁、1个压型、3个弯曲和1个切断工序构成的排样图，设计了双侧载体，材料利用率达到48.9%。圆形小直径孔冲裁凸模设计成过渡台肩结构，提升了模具强度，设计了快换式固定方式，凸模工作部分添加保护套，异形冲裁凸模采用单侧挂台方式定位，凹模均采用凹模镶块结构。压型凸模安装在卸料板上，保证了压型深度和精度。复杂Z字形弯曲，采用向上弯曲和向下弯曲两步弯曲结构，向上弯曲凸模安装在卸料板上，保证了弯曲精度和正常卸料、压边。

The stamping process analysis was carried out for a connector. By comparing the two layout methods, a layout chart consisted of five blanking steps, one profiling step, three bending steps and one cutting step was designed and optimized, the bilateral carrier was designed, and the material utilization reached 48.9%. However, piercing punches with small apertures were designed as transitional shoulder structures to enhance the strength of die. The quick-change fixing type was designed, the working part of punch was added the protective sleeve, and the abnormity piercing punches were positioned by one-side hanging table. The dies were designed as an insert block structure. Then, the profiling punch was installed on the unloading plate to ensure the depth and precision of profiling. Furthermore, the complex Z-shaped bending adopts two-step bending structures of upward bending and downward bending, the upward bending punches were installed on the unloading plate, and the accuracy of bending and the correctness of discharge and blank holder could be ensured.

基金项目：

河北省高等学校自然科学研究青年基金项目(QN2016229)；河北科技大学理工学院教研项目(2015Z01，ZX2016Y02)

作者简介：闫华军(1978-)，男，博士，副教授，E-mail：yanhj22@163.com

参考文献：

[1]姜伯军. 级进冲模设计与模具结构实例[M]. 北京: 机械工业出版社, 2008.

Jiang B J. Progressive Die Design and Die Structure Example[M]. Beijing: China Machine Press, 2008.

[2]陈炎嗣.多工位级进模设计与制造[M].北京:机械工业出版社, 2006.

Chen Y S. Design and Manufacture of Multi-position Progressive Die[M]. Beijing: China Machine Press, 2006.

[3]丁明明，蔡丹云，黄勇. 非对称法兰密封固定盖级进模设计[J]. 锻压技术, 2013,38(3):122-124.

Ding M M, Cai D Y, Huang Y. Design of progressive die for sealing fixing cover with asymmetric flange[J]. Forging & Stamping Technology, 2013,38(3):122-124.

[4]闫华军, 王丽娟. 叉形导电件的多工位级进模设计[J]. 锻压技术, 2015, 40(4):106-109.

Yan H J, Wang L J. Design of multi-position progressive die for fork-shaped electrical conductive part[J]. Forging & Stamping Technology, 2015, 40(4):106-109.

[5]闫华军, 王峰, 刘玉忠, 等. 书夹件多工位级进模设计[J]. 热加工工艺, 2014, 43(11): 120-122.

Yan H J, Wang F, Liu Y Z, et al. Design of multistation progressive die for bookend parts[J]. Hot Working Technology, 2014, 43(11): 120-122.

[6]姜伯军. 屏蔽罩壳盖级进模设计[J]. 模具制造, 2011, (2): 46-49.

Jiang B J. Design of progressive die for the shielded enclosure cover[J]. Die & Mould Manufacture, 2011, (2): 46-49.

[7]戴茂良. 锁片多工位级进模的设计[J]. 锻压技术, 2011,34(6): 88-90.

Dai M L. Design of multi-position progressive die for lock-chip[J]. Forging & Stamping Technology, 2011,34(6): 88-90.

[8]葛允尧, 王蕾. 插件端子多工位级进模设计[J]. 锻压装备与制造技术, 2011, 46(3): 90-93.

Ge Y Y, Wang L. Design of a multi-position progressive die for connector terminals[J]. China Metalforming Equipment & Manufacturing Technology, 2011, 46(3): 90-93.

[9]周美蓉，沈言锦. JBSAN盖板冲压工艺与模具设计[J], 模具工业, 2011, 37(6): 35-38.

Zhou M R, Shen Y J. Stamping process and design of die for JBSAN cover plate[J]. Die & Mould Industry, 2011,37(6): 35-38.

[10]刘占军. 双角片件多工位级进模设计[J]. 锻压技术, 2008, 33(2): 84-86.

Liu Z J. Design of multi-position progressive die for double angle piece parts[J]. Forging & Stamping Technology, 2008, 33(2): 84-86.

[11]何开峰, 刘联平. 弹簧连接件级进模设计[J]. 模具工业, 2011, 37(7): 19-20.

He K F, Liu L P. Development of progressive die for spring connector[J]. Die & Mould Industry, 2011, 37(7): 19-20.

服务与反馈：

【文章下载】【加入收藏】