锻压技术

Ti-6Al-4V-2Fe合金的多向锻造工艺有限元模拟及微观组织研究

英文标题：FEM simulation and microstructure investigation on multi-directional forging process for alloy Ti-6Al-4V-2Fe

作者：张毅宁张悦李萍孟庆刚

分类号：TG316.2

出版年,卷(期):页码：2017,42(8):12-16

摘要：

采用有限元方法，对Ti-6Al-4V-2Fe合金的9次换向锻造工艺过程进行了热力耦合数值模拟，获得了合金在该变形工艺下的温度场和应变场的演化规律，并结合温度计算结果，分析了合金锻件内部6个典型位置的金相组织。研究结果表明：工件内大部分区域的变形在β单相区完成，由于这部分区域的降温速率和变形量均较小，所以转变组织为片层状魏氏组织，并存在明显的原始β晶界；在工件表面区域，由于变形温度很快降至α+β两相区内，所以最终转变为网篮组织；随着换向锻造工艺的逐步进行，工件内部的等效应变量逐步增加，锻后等效应变值的分布由中心向表面逐渐减小。

Nine forging processes with different directions of alloy Ti-6Al-4V-2Fe were conducted by thermo-mechanical coupled simulation, and the temperature field and equivalent strain field during whole deformation processes were obtained. Then, the microstructures at six typical positions in workpiece were analyzed combining with the temperature calculation result. The results indicate that the most of deformation interior to the workpiece is conducted on β single phase region, and the lamellar Widmanstatten structure with primitive β grain boundary can be observed because of the small cooling rate and deformation. Finally, because the temperature cools into α+β double phase regions with high cooling rate, the workpiece surface transformes to basket weave structure. Thus, the equivalent strain increases as the forging step is gradually carried out, and the equivalent strain deceases gradually from center to surface.

基金项目：

国家自然科学基金资助项目(11275007)

张毅宁（1974-），男，学士，实验师张悦（1963-），女，学士，副教授

参考文献：

［1］牛立群，张琦，解明，等. 基于FORGE-3D径向锻造工艺的数值模拟[J]. 锻压技术，2017，42(2)：167-171.Niu L Q, Zhang Q, Xie M, et al. Numerical simulation of radial forging process based on FORGE-3D[J]. Forging & Stamping Technology, 2017, 42(2): 167-171.
［2］张学奇，董万鹏，苏钰，等. 基于Deform-3D的花键轴叉热锻成形工艺优化[J]. 锻压技术，2017，42(1)：5-9.Zhang X Q, Dong W P, Su Y, et al. Process optimization on hot forging for spline shaft fork based on Deform-3D[J]. Forging & Stamping Technology, 2017, 42(1): 5-9.
［3］张伟，夏高宇，王强，等. 转向轴承套圈温锻成形工艺的有限元模拟[J]. 锻压技术，2017，41(12)：14-25.Zhang W, Xia G Y, Wang Q, et al. Finite element analysis on warm forging process for steering bearing rings[J]. Forging & Stamping Technology, 2016, 41(12): 14-25.
［4］刘健光，刘风雷，刘华东，等.钛合金球形头骨钉镦锻加工工艺流程及性能研究[J].锻压技术，2016，41(12)：8-13.Liu J G，Liu F L，Liu H D，et al. Study on upsetting process and property for titanium alloy spherical bone screws [J].Forging & Stamping Technology，2016，41(12)：8-13.
［5］张明杰，黄利军，李恒正，等.基于有限元仿真的钛合金翼形件锻造过程[J].锻压技术，2016，41(11)：32-37.Zhang M J，Huang L J，Li H Z，et al. Forging process of titanium alloy winglike part based on FEM simulation method [J]. Forging & Stamping Technology，2016，41(11)：32-37.
［6］徐坤和，张文学，阳代军. 9 m级超大直径2219铝合金整体环件的研制[J].锻压技术，2016，41(10)：92-97.Xu K H，Zhang W X，Yang D J. Manufacture of aluminum alloy 2219 integral ring with 9 m ultra-large diameter[J]. Forging & Stamping Technology，2016，41(10)：92-97.
［7］梁恩泉，黄森森，马英杰，等.Fe对Ti-6Al-4V ELI合金力学性能的影响[J].材料研究学报，2016，30(4)：299-306.Liang E Q, Huang S S, Ma Y J, et al. The influence of Fe on the mechanical properties of Ti-6Al-4V ELI alloy [J]. Chinese Journal of Materials Research, 2016, 30(4): 299-306.

服务与反馈：

【文章下载】【加入收藏】