锻压技术

变形温度对反挤压耐磨锡青铜合金组织性能的影响

英文标题：Influence of deformation temperature on microstructure and property of wear-resisting tin bronze alloy prepared by inverse extrusion process

作者：魏炜张文琼

单位：宁德职业技术学院厦门大学嘉庚学院

关键词：Cu-Sn-Pb-Ni 锡青铜反挤压变形温度密度硬度微观组织

分类号：TG146.1

出版年,卷(期):页码：2017,42(8):62-65

摘要：

针对锡含量9%~11%的耐磨Cu-Sn-Pb-Ni锡青铜合金，进行了800~950 ℃、不同工艺条件下的反挤压成形工艺试验，测试了经塑性变形后合金的密度、硬度和强度等性能，分析了不同工艺条件下合金的微观组织，并与传统熔铸法制备的合金性能及微观组织进行了对比。结果表明：传统熔铸法制备的合金密度和硬度分别为8.8893 g·cm-3和116 HB，经不同温度反挤压塑性变形后，密度和硬度均有所提高；经900 ℃挤压后，密度和硬度分别达9.0409 g·cm-3和139 HB；较之铸态下树枝晶明显，微观组织为α固溶体+（α+δ）共析体，挤压后合金组织晶粒明显细小和致密；在试验范围内，该合金的最佳反挤压塑性成形温度为900 ℃。

For the high-tin wear-resisting Cu-Sn-Pb-Ni alloy with the tin content 9%-11%, the inverse extrusion experiments were conducted under different technological conditions within 800-950 ℃, and the density, hardness and strength of alloy were tested. Then, the alloy microstructure was analyzed under different technological conditions, and the properties and microstructure of alloy prepared by traditional melt casting method were compared. The results show that the density and hardness of Cu-Sn-Pb-Ni alloy prepared by traditional melt casting method are 8.8893 g·cm-3 and 116 HB separately, and the density and hardness are increased after inverse extrusion at different temperatures. Especially after inverse extrusion at 900 ℃, the density and hardness reach the maximum values 9.0409 g·cm-3 and 139 HB respectively. Compared with the as-cast, microstructure is mainly obvious dendrite structure which is α solid solution and eutectoid（α+δ）, and microstructure of alloy grain is obviously refined and densed after extrusion. Within the range of experiments, the best inverse extrusion temperature of alloy is 900 ℃.

基金项目：

福建省教育厅基金项目（JA15870）

魏炜（1980-），男，硕士，讲师

参考文献：

［1］杨华龙，樊文欣，曹存存，等. 发动机连杆衬套毛坯温挤压工艺研究及模具设计[J]. 锻压技术，2016，41(8)：79-82.Yang H L, Fan W X, Cao C C, et al. Research and die design on warm extrusion technology for engine connecting rod bushing [J]. Forging & Stamping Technology, 2012，41(8):79-82.
［2］苏晓波，冯再新，高超平，等. 加热温度对锡青铜挤压成形后组织性能的影响[J]. 锻压技术，2017，42(2)：156-159.Su X B, Feng Z X, Gao C P, et al. Effect of heating temperature on microstructure and mechanical properties for tin bronze after extrusion[J]. Forging & Stamping Technology, 2017，42(2):156-159.
［3］林国标，王自东，张伟，等. 热处理对锡青铜合金组织和性能的影响[J]. 铸造，2011，60 (3)：287-289.Lin G B, Wang Z D, Zhang W, et al. Effects of heat treatment on microstructure and properties of tin bronze alloys[J]. Casting, 2011, 60(3): 287-289.
［4］李乃拥，段志科，李通，等. 成形比压对ZCuSn10P1锡青铜半固态组织的影响[J]. 特种铸造及有色合金，2017，37 (3)：273-276.Li N Y, Duan Z K, Li T, et al. Effects of forming specific pressure on microstructure of the semi-solid ZCuSn10P1 tin bronze [J]. Special Casting & Nonferrous Alloys, 2017, 37(3): 273-276.
［5］游龙，伊勇臻，王可可，等. 形变热处理对铸造锡青铜组织与力学性能的影响[J]. 金属热处理，2016，41(1)：71-73.You L, Yi Y Z, Wang K K, et al. Effect of thermomechanical treatment on microstructure and mechanical properties of casting tin bronze [J]. Hot Working Technology, 2016, 45(5):71-73.
［6］王明杰，张国伟，刘少杰. 微量元素对铅锡青铜组织与性能的影响[J]. 热加工工艺，2016，45(5)：87-89.Wang M J, Zhang G W, Liu S J. Effects of trace elements on microstructure and properties of lead-tin bronze[J]. Hot Working Technology, 2016, 45(5):87-89.
［7］Aksoy M, Kuzucu V, Turhan H. A note on the effect of phosphorus on the microstructure and mechanical properties of leaded-tin bronze [J].Materials Processing Technology, 2002,124: 113-115.

服务与反馈：

【文章下载】【加入收藏】