锻压技术

从动螺旋锥齿轮双锥辊辗压成形工艺参数优化

英文标题：Optimization on process parameters of double cone roller rolling for driven spiral bevel gear

作者：刘赣华钱锦年张振铎邹洋

单位：江西理工大学

分类号：TG316.3；TH122

出版年,卷(期):页码：2017,42(10):81-85

摘要：

针对双锥辊辗压螺旋锥齿轮成形过程中型腔下模受力过大以及齿形充填高度不够的问题，首先，运用DEFORM-3D有限元软件对从动螺旋锥齿轮齿坯双锥辊辗压过程进行了模拟分析，研究了摩擦系数、辗压温度、凹模型腔进给速度对凹模型腔等效应力和Z方向成形齿高的影响；其次，采用正交试验设计方法，以凹模型腔等效应力和Z方向成形齿高为优化指标，得到了最佳工艺参数，并进行了数值验证；最后，通过数值计算分析以及与文献中研究结果进行比较分析，证明了从动螺旋锥齿轮双锥辊辗压成形工艺的可行性。结果表明：当摩擦系数为0.2、辗压温度为900 ℃、凹模型腔进给速度为2 mm·s-1时，模具型腔受力最小，齿形的充填饱满，高度达到最高。

For the problems of excessive force acting on the concave cavity and insufficient filling of tooth height during the forming of the double cone roller rolling for spiral bevel gear, the rolling process of double cone roller for the driven spiral bevel gear was simulated by finite element software DEFORM3D firstly, and the influences of friction coefficient, rolling temperature, feeding velocity of concave cavity on the equivalent stress of concave cavity and the forming tooth height along Zdirection were studied. Secondly, the optimum process parameters were obtained and verified numerically by the orthogonal test design method with the optimized indexes of the equivalent stress of concave cavity and the forming tooth height along Zdirection. Finally, the feasibility of double cone roller rolling process for driven spiral bevel gear was proved by numerical analysis and compared with the results in the literature. The results show that when the friction coefficient is 0.2, the rolling temperature is 900 ℃, and the feeding velocity of concave cavity is 2 mm·s-1, the force of concave cavity is the smallest, and the filling of tooth shape is full with the highest tooth height.

基金项目：

江西省教育厅科学技术研究项目（GJJ13417）

作者简介：刘赣华（1973-），女，硕士，副教授，E-mail：770776237@qq.com；通讯作者：钱锦年（1992-），男，硕士研究生，E-mail：153203117@qq.com

参考文献：

[1]曾韬.螺旋锥齿轮设计与加工[M].哈尔滨：哈尔滨工业大学出版社，1989.

Zeng T. Design and Manufacture of Spiral Bevel Gears [M]. Harbin: Harbin Institute of Technology Press, 1989.

[2]赵海宾. 基于响应面汽车变速器螺旋伞齿轮精锻成形工艺优化[J]. 锻压技术,2016,41(4):10-13.

Zhao H B. Process optimization of precision forging for auto transmission spiral bevel gears based on response surface[J]. Forging & Stamping Technology, 2016, 41 (4): 10-13.

[3]Duggirala R. Design of forging dies for forming flashless ring gear blanks using finite element methods[J]. Journal of Materials Shaping Technology, 1989, 7(1):33-47.

[4]Choi J C, Choi Y, Tak S J. The forging of helical gears (I): Experiments and upperbound analysis[J]. International Journal of Mechanical Sciences, 1998, 40(4):325-337.

[5]Choi J C, Choi Y, Tak S J. The forging of helical gears (II): Comparisons of the forging processes[J]. International Journal of Mechanical Sciences, 1999, 41 (6):725-739.

[6]胡亚民. WGSHΦ800双锥辊辗压机研制成功[J].锻压技术,2003, 28(2):69.

Hu Y M. WGSHΦ800 twin cone rolls mill is developed successfully[J]. Forging & Stamping Technology, 2003, 28(2): 69.

[7]程孟彪. 从动螺旋齿轮坯成形工艺优化[D]. 武汉：武汉理工大学,2011.

Cheng M B. Optimization of Forming Process of Driven Spiral Bevel Gear [D]. Wuhan：Wuhan University of Technology, 2011.

[8]朱春东,史双喜,华林. 对称双辊轴向轧制从动螺旋锥齿轮新工艺[J]. 中国机械工程, 2009, 20(15):1877-1879.

Zhu C D, Shi S X, Hua L. New technology of twin symmetry roll axial rolling passive spiral bevel gears [J]. China Mechanical Engineering, 2009, 20(15):1877-1879.

[9]吴涛. 双锥辊辗压成形工艺分析与应用研究[D].武汉：武汉理工大学,2007.

Wu T. Analysis and Application Research on Rolling Forming Process of Double Cone Roller [D]. Wuhan：Wuhan University of Technology, 2007.

[10]张振铎. 从动螺旋锥齿轮双锥辊辗压成形工艺优化及模具型腔精确设计方法研究[D]. 赣州：江西理工大学，2016.

Zhang Z D. Optimization of Double Cone Roll Forging Process of Driven Spiral Bevel Gear and Design of Accurate Design of Die Cavity [D]. Ganzhou：Jiangxi University of Science and Technology, 2016.

[11]史双喜. 螺旋锥齿轮双锥辊辗压成形有限元模拟[J]. 热加工工艺, 2010, 39(11):126-128, 132.

Shi S X. Finite element simulation of twin cone roll forging spiral bevel gear [J]. Hot Working Technology, 2010, 39(11):126-128, 132.

服务与反馈：

【文章下载】【加入收藏】